tcp (4)

Leading comments

 Copyright (c) 1983, 1991, 1993
	The Regents of the University of California.
 Copyright (c) 2010-2011 The FreeBSD Foundation
 All rights reserved.

 Portions of this documentation were written at the Centre for Advanced
 Internet Architectures, Swinburne University of Technology, Melbourne,
 Australia by David Hayes under sponsorship from the FreeBSD Foundation.

 Redistribution and use in source and binary forms, with or without
 modification, are permitted provided that the following condi...

(The comments found at the beginning of the groff file "man4/tcp.4freebsd".)

NAME

tcp - Internet Transmission Control Protocol

SYNOPSIS

In sys/types.h In sys/socket.h In netinet/in.h In netinet/tcp.h Ft int Fn socket AF_INET SOCK_STREAM 0

DESCRIPTION

The TCP protocol provides reliable, flow-controlled, two-way transmission of data. It is a byte-stream protocol used to support the SOCK_STREAM abstraction. TCP uses the standard Internet address format and, in addition, provides a per-host collection of ``port addresses'' Thus, each address is composed of an Internet address specifying the host and network, with a specific TCP port on the host identifying the peer entity.

Sockets utilizing the TCP protocol are either ``active'' or ``passive'' Active sockets initiate connections to passive sockets. By default, TCP sockets are created active; to create a passive socket, the listen(2) system call must be used after binding the socket with the bind(2) system call. Only passive sockets may use the accept(2) call to accept incoming connections. Only active sockets may use the connect(2) call to initiate connections.

Passive sockets may ``underspecify'' their location to match incoming connection requests from multiple networks. This technique, termed ``wildcard addressing'' allows a single server to provide service to clients on multiple networks. To create a socket which listens on all networks, the Internet address INADDR_ANY must be bound. The TCP port may still be specified at this time; if the port is not specified, the system will assign one. Once a connection has been established, the socket's address is fixed by the peer entity's location. The address assigned to the socket is the address associated with the network interface through which packets are being transmitted and received. Normally, this address corresponds to the peer entity's network.

TCP supports a number of socket options which can be set with setsockopt(2) and tested with getsockopt(2):

TCP_INFO

Information about a socket's underlying TCP session may be retrieved by passing the read-only option TCP_INFO to getsockopt(2). It accepts a single argument: a pointer to an instance of Vt struct tcp_info .

This API is subject to change; consult the source to determine which fields are currently filled out by this option. Fx specific additions include send window size, receive window size, and bandwidth-controlled window space.

TCP_CONGESTION

Select or query the congestion control algorithm that TCP will use for the connection. See mod_cc4 for details.

TCP_KEEPINIT

This setsockopt(2) option accepts a per-socket timeout argument of Vt u_int in seconds, for new, non-established TCP connections. For the global default in milliseconds see keepinit in the Sx MIB Variables section further down.

TCP_KEEPIDLE

This setsockopt(2) option accepts an argument of Vt u_int for the amount of time, in seconds, that the connection must be idle before keepalive probes (if enabled) are sent for the connection of this socket. If set on a listening socket, the value is inherited by the newly created socket upon accept(2). For the global default in milliseconds see keepidle in the Sx MIB Variables section further down.

TCP_KEEPINTVL

This setsockopt(2) option accepts an argument of Vt u_int to set the per-socket interval, in seconds, between keepalive probes sent to a peer. If set on a listening socket, the value is inherited by the newly created socket upon accept(2). For the global default in milliseconds see keepintvl in the Sx MIB Variables section further down.

TCP_KEEPCNT

This setsockopt(2) option accepts an argument of Vt u_int and allows a per-socket tuning of the number of probes sent, with no response, before the connection will be dropped. If set on a listening socket, the value is inherited by the newly created socket upon accept(2). For the global default see the keepcnt in the Sx MIB Variables section further down.

TCP_NODELAY

Under most circumstances, TCP sends data when it is presented; when outstanding data has not yet been acknowledged, it gathers small amounts of output to be sent in a single packet once an acknowledgement is received. For a small number of clients, such as window systems that send a stream of mouse events which receive no replies, this packetization may cause significant delays. The boolean option TCP_NODELAY defeats this algorithm.

TCP_MAXSEG

By default, a sender- and receiver- TCP will negotiate among themselves to determine the maximum segment size to be used for each connection. The TCP_MAXSEG option allows the user to determine the result of this negotiation, and to reduce it if desired.

TCP_NOOPT

TCP usually sends a number of options in each packet, corresponding to various TCP extensions which are provided in this implementation. The boolean option TCP_NOOPT is provided to disable TCP option use on a per-connection basis.

TCP_NOPUSH

By convention, the sender- TCP will set the ``push'' bit, and begin transmission immediately (if permitted) at the end of every user call to write(2) or writev(2). When this option is set to a non-zero value, TCP will delay sending any data at all until either the socket is closed, or the internal send buffer is filled.

TCP_MD5SIG

This option enables the use of MD5 digests (also known as TCP-MD5) on writes to the specified socket. Outgoing traffic is digested; digests on incoming traffic are verified if the net.inet.tcp.signature_verify_input sysctl is nonzero. The current default behavior for the system is to respond to a system advertising this option with TCP-MD5; this may change.

One common use for this in a Fx router deployment is to enable based routers to interwork with Cisco equipment at peering points. Support for this feature conforms to RFC 2385. Only IPv4 (AF_INET ) sessions are supported.

In order for this option to function correctly, it is necessary for the administrator to add a tcp-md5 key entry to the system's security associations database (SADB) using the setkey(8) utility. This entry must have an SPI of 0x1000 and can therefore only be specified on a per-host basis at this time.

If an SADB entry cannot be found for the destination, the outgoing traffic will have an invalid digest option prepended, and the following error message will be visible on the system console: tcp_signature_compute: SADB lookup failed for %d.%d.%d.%d

The option level for the setsockopt(2) call is the protocol number for TCP available from getprotobyname(3), or IPPROTO_TCP All options are declared in In netinet/tcp.h .

Options at the IP transport level may be used with TCP see ip(4). Incoming connection requests that are source-routed are noted, and the reverse source route is used in responding.

The default congestion control algorithm for TCP is cc_newreno4. Other congestion control algorithms can be made available using the mod_cc4 framework.

MIB Variables

The TCP protocol implements a number of variables in the net.inet.tcp branch of the sysctl(3) MIB.

TCPCTL_DO_RFC1323

(rfc1323 ) Implement the window scaling and timestamp options of RFC 1323 (default is true).

TCPCTL_MSSDFLT

(mssdflt ) The default value used for the maximum segment size (``MSS'' ) when no advice to the contrary is received from MSS negotiation.

TCPCTL_SENDSPACE

(sendspace ) Maximum TCP send window.

TCPCTL_RECVSPACE

(recvspace ) Maximum TCP receive window.

log_in_vain

Log any connection attempts to ports where there is not a socket accepting connections. The value of 1 limits the logging to SYN (connection establishment) packets only. That of 2 results in any TCP packets to closed ports being logged. Any value unlisted above disables the logging (default is 0, i.e., the logging is disabled).

msl

The Maximum Segment Lifetime, in milliseconds, for a packet.

keepinit

Timeout, in milliseconds, for new, non-established TCP connections. The default is 75000 msec.

keepidle

Amount of time, in milliseconds, that the connection must be idle before keepalive probes (if enabled) are sent. The default is 7200000 msec (2 hours).

keepintvl

The interval, in milliseconds, between keepalive probes sent to remote machines, when no response is received on a keepidle probe. The default is 75000 msec.

keepcnt

Number of probes sent, with no response, before a connection is dropped. The default is 8 packets.

always_keepalive

Assume that SO_KEEPALIVE is set on all TCP connections, the kernel will periodically send a packet to the remote host to verify the connection is still up.

icmp_may_rst

Certain ICMP unreachable messages may abort connections in SYN-SENT state.

do_tcpdrain

Flush packets in the TCP reassembly queue if the system is low on mbufs.

blackhole

If enabled, disable sending of RST when a connection is attempted to a port where there is not a socket accepting connections. See blackhole(4).

delayed_ack

Delay ACK to try and piggyback it onto a data packet.

delacktime

Maximum amount of time, in milliseconds, before a delayed ACK is sent.

path_mtu_discovery

Enable Path MTU Discovery.

tcbhashsize

Size of the TCP control-block hash table (read-only). This may be tuned using the kernel option TCBHASHSIZE or by setting net.inet.tcp.tcbhashsize in the loader(8).

pcbcount

Number of active process control blocks (read-only).

syncookies

Determines whether or not SYN cookies should be generated for outbound SYN-ACK packets. SYN cookies are a great help during SYN flood attacks, and are enabled by default. (See syncookies(4).)

isn_reseed_interval

The interval (in seconds) specifying how often the secret data used in RFC 1948 initial sequence number calculations should be reseeded. By default, this variable is set to zero, indicating that no reseeding will occur. Reseeding should not be necessary, and will break TIME_WAIT recycling for a few minutes.

rexmit_min , rexmit_slop

Adjust the retransmit timer calculation for TCP The slop is typically added to the raw calculation to take into account occasional variances that the SRTT (smoothed round-trip time) is unable to accommodate, while the minimum specifies an absolute minimum. While a number of TCP RFCs suggest a 1 second minimum, these RFCs tend to focus on streaming behavior, and fail to deal with the fact that a 1 second minimum has severe detrimental effects over lossy interactive connections, such as a 802.11b wireless link, and over very fast but lossy connections for those cases not covered by the fast retransmit code. For this reason, we use 200ms of slop and a near-0 minimum, which gives us an effective minimum of 200ms (similar to Linux )

rfc3042

Enable the Limited Transmit algorithm as described in RFC 3042. It helps avoid timeouts on lossy links and also when the congestion window is small, as happens on short transfers.

rfc3390

Enable support for RFC 3390, which allows for a variable-sized starting congestion window on new connections, depending on the maximum segment size. This helps throughput in general, but particularly affects short transfers and high-bandwidth large propagation-delay connections.

sack.enable

Enable support for RFC 2018, TCP Selective Acknowledgment option, which allows the receiver to inform the sender about all successfully arrived segments, allowing the sender to retransmit the missing segments only.

sack.maxholes

Maximum number of SACK holes per connection. Defaults to 128.

sack.globalmaxholes

Maximum number of SACK holes per system, across all connections. Defaults to 65536.

maxtcptw

When a TCP connection enters the TIME_WAIT state, its associated socket structure is freed, since it is of negligible size and use, and a new structure is allocated to contain a minimal amount of information necessary for sustaining a connection in this state, called the compressed TCP TIME_WAIT state. Since this structure is smaller than a socket structure, it can save a significant amount of system memory. The net.inet.tcp.maxtcptw MIB variable controls the maximum number of these structures allocated. By default, it is initialized to kern.ipc.maxsockets / 5.

nolocaltimewait

Suppress creating of compressed TCP TIME_WAIT states for connections in which both endpoints are local.

fast_finwait2_recycle

Recycle TCP FIN_WAIT_2 connections faster when the socket is marked as SBS_CANTRCVMORE (no user process has the socket open, data received on the socket cannot be read). The timeout used here is finwait2_timeout

finwait2_timeout

Timeout to use for fast recycling of TCP FIN_WAIT_2 connections. Defaults to 60 seconds.

ecn.enable

Enable support for TCP Explicit Congestion Notification (ECN). ECN allows a TCP sender to reduce the transmission rate in order to avoid packet drops.

ecn.maxretries

Number of retries (SYN or SYN/ACK retransmits) before disabling ECN on a specific connection. This is needed to help with connection establishment when a broken firewall is in the network path.

ERRORS

A socket operation may fail with one of the following errors returned:

Bq Er EISCONN

when trying to establish a connection on a socket which already has one;

Bq Er ENOBUFS

when the system runs out of memory for an internal data structure;

Bq Er ETIMEDOUT

when a connection was dropped due to excessive retransmissions;

Bq Er ECONNRESET

when the remote peer forces the connection to be closed;

Bq Er ECONNREFUSED

when the remote peer actively refuses connection establishment (usually because no process is listening to the port);

Bq Er EADDRINUSE

when an attempt is made to create a socket with a port which has already been allocated;

Bq Er EADDRNOTAVAIL

when an attempt is made to create a socket with a network address for which no network interface exists;

Bq Er EAFNOSUPPORT

when an attempt is made to bind or connect a socket to a multicast address.

SEE ALSO

getsockopt(2), socket(2), sysctl(3), blackhole(4), inet(4), intro(4), ip(4), mod_cc4, siftr(4), syncache(4), setkey(8)

"V. Jacobson" "R. Braden" "D. Borman" "TCP Extensions for High Performance" "RFC 1323"

"A. Heffernan" "Protection of BGP Sessions via the TCP MD5 Signature Option" "RFC 2385"

"K. Ramakrishnan" "S. Floyd" "D. Black" "The Addition of Explicit Congestion Notification (ECN) to IP" "RFC 3168"

HISTORY

The TCP protocol appeared in BSD 4.2 The RFC 1323 extensions for window scaling and timestamps were added in BSD 4.4 The TCP_INFO option was introduced in Linux 2.6 and is subject to change