upgt (4)

Leading comments

$OpenBSD: upgt.4,v 1.6 2008/04/17 14:01:22 jmc Exp $
$FreeBSD: releng/11.0/share/man/man4/upgt.4 275591 2014-12-08 04:06:03Z mp $

Copyright (c) 2007 Marcus Glocker <mglocker@openbsd.org>
Copyright (c) 2005-2007
    Damien Bergamini <damien.bergamini@free.fr>

Permission to use, copy, modify, and distribute this software for any
purpose with or without fee is hereby granted, provided that the above
copyright notice and this permission notice appear in all copies.

THE SOFTWARE IS PROVIDED "AS...

(The comments found at the beginning of the groff file "man4/upgt.4freebsd".)

NAME

upgt - Conexant/Intersil PrismGT SoftMAC USB IEEE 802.11b/g wireless network device

SYNOPSIS

To compile this driver into the kernel, place the following lines in your kernel configuration file:

device ehci device uhci device ohci device usb device upgt device wlan

Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:

if_upgt_load="YES"

DESCRIPTION

The ifconfig driver supports the USB 2.0 Conexant/Intersil PrismGT series wireless adapters based on the GW3887 chipset.

These are the modes the ifconfig driver can operate in:

BSS mode

Also known as infrastructure mode, this is used when associating with an access point, through which all traffic passes. This mode is the default.

monitor mode

In this mode the driver is able to receive packets without associating with an access point. This disables the internal receive filter and enables the card to capture packets from networks which it wouldn't normally have access to, or to scan for access points.

ifconfig supports software WEP. Wired Equivalent Privacy (WEP) is the de facto encryption standard for wireless networks. It can be typically configured in one of three modes: no encryption; 40-bit encryption; or 104-bit encryption. Unfortunately, due to serious weaknesses in WEP protocol it is strongly recommended that it not be used as the sole mechanism to secure wireless communication. WEP is not enabled by default.

The ifconfig driver can be configured at runtime with ifconfig(8).

FILES

This driver requires the upgtfw firmware to be installed before it will work. The firmware files are not publicly available. A package of the firmware which can be installed via pkg_add1 is available:

weongyo.org/project/upgt/upgt-firmware-2.13.1.0.tar.gz

HARDWARE

The ifconfig driver supports USB 2.0 Conexant/Intersil PrismGT series wireless adapters based on the GW3887 chipset, among them:

• Belkin F5D7050 (version 1000)
• Cohiba Proto Board
• D-Link DWL-G120 Cohiba
• FSC Connect2Air E-5400 USB D1700
• Gigaset USB Adapter 54
• Inventel UR045G
• SMC EZ ConnectG SMC2862W-G
• Sagem XG703A
• Spinnaker DUT
• Spinnaker Proto Board

EXAMPLES

Join an existing BSS network (i.e., connect to an access point):

ifconfig wlan create wlandev upgt0 inet 192.168.0.20 \
    netmask 0xffffff00

Join a specific BSS network with network name ``my_net ''

"ifconfig wlan create wlandev upgt0 ssid my_net up"

Join a specific BSS network with 64-bit WEP encryption:

ifconfig wlan create wlandev upgt0 ssid my_net \
        wepmode on wepkey 0x1234567890 weptxkey 1 up

SEE ALSO

arp(4), netintro(4), usb(4), wlan(4), ifconfig(8)

HISTORY

The ifconfig driver first appeared in Ox 4.3 .

AUTHORS

An -nosplit The ifconfig driver was written by An Marcus Glocker Aq mglocker@openbsd.org .

The hardware specification was reverse engineered by the people at www.prism54.org

CAVEATS

The ifconfig driver just supports the USB 2.0 devices (GW3887 chipset) but not the USB 1.0 devices containing the NET2280, ISL3880, and ISL3886 chipsets. Some further efforts would be necessary to add USB 1.0 support to the driver.