laptop-mode.conf (8)

NAME

/etc/laptop-mode/laptop-mode.conf - Configuration file for laptop-mode-tools.

DESCRIPTION

This manual page documents the options that can be set in the /etc/laptop-mode/laptop-mode.conf configuration file and in the modular configuration files in the /etc/laptop-mode/conf.d directory. For a description of what laptop mode does, see the laptop_mode(8) manual page.

SETTINGS

The syntax of options is OPTION=value. There are some groups of options that specify values depending on power state and laptop mode is enabled. These use the prefix "LM_" to indicate that a value is used only when laptop mode is enabled, "NOLM_" to indicate the opposite, "AC_" to indicate that a value is used only when the system is running on AC power, and "BATT_" to indicate that a value is used only when the system is running on batteries. Settings are prefixed with a combination of an optional LM_/NOLM_ prefix and an optional AC_/BATT_. For instance, the combination LM_AC_ means "when the system is in laptop mode and on AC power". (Note that this situation happens only if ENABLE_LAPTOP_MODE_ALWAYS is enabled!) If one of the prefixes (either LM_/NOLM_ or AC_/BATT_) is missing, then the value is used independently of the state of laptop mode or AC power, respectively. Options that start with "CONTROL_" are boolean settings that determine whether laptop mode tools is allowed to control a certain aspect of your system. Boolean settings always expect "0" to indicate the false (negative/no/disabled) value, and "1" to indicate the true (positive/yes/enabled) value.

The following sections list the settings that are available in laptop-mode.conf and in the modular configuration files.

Note: Many settings were moved from the main configuration file to the modular configuration files. The settings here are split out by modular configuration file, but in installations upgraded from version 1.36 or earlier they may appear in both. In such cases, the configuration settings in the main configuration file override those in the modular configuration files. To avoid confusion, it is advised to move the settings from the main configuration files to the modular configuration files when this situation is detected.

/etc/laptop-mode/conf.d/board-specific/

The board-specific settings framework is for users and distributors who would like to ship their local customized settings on top of the default settings shipped upstream.
Add local customized settings under this folder to override the system defaults.

/etc/laptop-mode/laptop-mode.conf

This is the main configuration file. It contains the settings for enabling and disabling, plus the core features: the Linux kernel laptop mode feature and related settings.

ENABLE_LAPTOP_MODE_TOOLS

This module determines if laptop-mode-tools should be run or not. Default is 1 Set it to 0 if you would like to completely disable laptop-mode-tools

VERBOSE_OUTPUT

Set this to 1 if you want to see a lot of output when you start/stop laptop mode, and to 0 if you don't want this. Useful for debugging purposes.

LOG_TO_SYSLOG

Set this to 1 if you want to log messages to syslog when you start/stop laptop mode, and to 0 if you don't want this. Useful for debugging purposes.

DEBUG

Set this to 1 if you would like to execute the entire laptop-mode program in debug mode. WARNING: This will create a lot of text output. If you are debugging an individual module, perhaps you would want to enable each module specific debug mode (available in module conf files)

ENABLE_AUTO_MODULES

Set this to 1 to enable all laptop mode tools modules that are termed safe to be enabled and are marked auto. With this option alone, you can enable all auto modules. Incase you need to fine-control the behavior of individual modules, you can modify them accordingly. Default is 1

ENABLE_LAPTOP_MODE_ON_BATTERY

ENABLE_LAPTOP_MODE_ON_AC

These options determine whether laptop mode will be activated when the computer is on battery or on AC power, respectively. Note that if the system service laptop-mode is not started, then laptop mode will never be started, even if this option is enabled.
 

ENABLE_LAPTOP_MODE_WHEN_LID_CLOSED

When this option is enabled, laptop mode will be activated when the laptop's lid is closed, even if the system is not working on batteries. Note that if the system service laptop-mode is not started, then laptop mode will never be started, even if this option is enabled. This feature is only supported on ACPI.
 

MINIMUM_BATTERY_CHARGE_PERCENT

The minimum number of battery minutes, charge (in mAh) or charge (in mWh) that you want to have available while your laptop is in laptop mode. When the number of minutes/mAhs/mWhs goes below this value, the data loss sensitive features are automatically disabled. Note that some batteries do not report a discharge rate, which means that MINIMUM_BATTERY_MINUTES has no effect for these batteries. These options are only supported on ACPI.

DISABLE_LAPTOP_MODE_ON_CRITICAL_BATTERY_LEVEL

If this option is enabled, the data loss sensitive features of laptop mode are disabled when the battery reports its state as "critical". This option is only supported on ACPI.

DISABLE_BATTERY_ALARM_CHECK

If this option is enabled, the alarm values are ignored from the battery. This is helpful if you have a broken battery which is reporting false alarms.

HD

The hard drives which laptop mode should operate upon. If you have multiple hard drives, you should list them all in this option, separated by spaces, for example: "/dev/hda /dev/hdb".

PARTITIONS

This option specifies the partitions or mount points that laptop mode should operate upon. Separate the partitions or mount points by spaces. You can include the entry "auto" to stand for the partitions on the hard drives specified in the HD option.
 

LM_BATT_MAX_LOST_WORK_SECONDS

LM_AC_MAX_LOST_WORK_SECONDS

The maximum number of seconds worth of data that you can lose when power runs out or when the computer crashes. This is the maximum number of seconds that laptop mode will keep modified data in memory without being written to disk. (Note that the NOLM value is missing: modifying this value when laptop mode is disabled is extremely useless, as it won't save you any power, and will only lose you work.)
 

CONTROL_READAHEAD

When this option is enabled, laptop mode tools controls the readahead on the filesystems it works upon.

LM_READAHEAD

NOLM_READAHEAD

The number of kilobytes to "read ahead" on your hard disks. Reading ahead means that whenever some data is read from disk, the data which is most likely to be accessed next is read as well, ahead of time. This then saves a hard disk spinup when the data is actually needed, because the data is then already in memory. Don't set this value too high, because the readahead applies to all files that are read!

CONTROL_NOATIME

When this option is enabled, laptop mode tools places the "noatime" option in the mount options of your filesystems when laptop mode is active. This option has the effect of disabling access time logging on files, which may save some disk activity. If you use programs that depend on access times (e.g., mutt), then you should disable this option, or enable the USE_RELATIME option.

USE_RELATIME

When this option is enabled together with the CONTROL_NOATIME option, laptop mode tools will use the relatime option instead of the noatime option. This option works for more applications, and still causes relatively low levels of disk writes. Note that this functionality is only available in recent kernel versions, and laptop mode tools will ignore this setting for kernels before 2.6.23.

CONTROL_HD_IDLE_TIMEOUT

When this option is enabled, laptop mode tools adjusts your hard drives' idle timeouts, i.e., the time of inactivity before they spin down.

LM_AC_HD_IDLE_TIMEOUT_SECONDS

LM_BATT_HD_IDLE_TIMEOUT_SECONDS

NOLM_HD_IDLE_TIMEOUT_SECONDS

These settings control the idle timeout for your hard drives. The values are specified in seconds. Values up to 20 minutes can be represented accurately by the hardware, anything above that is rounded down to half-hour precision. Use the value 0 to disable idle timeout.

CONTROL_HD_POWERMGMT

When this option is enabled, laptop mode tools adjusts your hard drives' power management settings.

BATT_HD_POWERMGMT

LM_AC_HD_POWERMGMT

NOLM_AC_HD_POWERMGMT

These values specify the power management level for your hard drives. The legal values for these options can be found in the hdparm(8) manual page, in the documentation of the -B option.

CONTROL_HD_WRITECACHE

When this option is enabled, laptop mode tools controls your hard drives' write cache settings.

NOLM_AC_HD_WRITECACHE

NOLM_BATT_HD_WRITECACHE

LM_HD_WRITECACHE

These options specify whether the write caches should be enabled for your hard drives.

CONTROL_SYSLOG_CONF (deprecated)

When this option is enabled, laptop mode tools controls /etc/syslog.conf as a symlink. This option is deprecated. Use the configuration-file-control module instead, which is configured in the /etc/laptop-mode/conf.d/configuration-file-control.conf module configuration file.

Advanced laptop-mode.conf options

These options normally do not need to be modified from their default values. Do not tweak these settings unless you know what you are doing.

ASSUME_SCSI_IS_SATA

This option, enabled by default, tells laptop mode tools to assume that a device /dev/sdX is a SATA device, and that it should be controlled using hdparm. If your /dev/sdX drives are really SCSI drives, disable this option.

ACPI_WITHOUT_AC_EVENTS

Enable this option if you have a laptop with a buggy ACPI implementation that doesn't send out AC adapter events. Enabling this option will make laptop mode check the AC adapter state whenever the battery state changes, which achieves just about the same effect as responding to AC adapter events.

CONTROL_MOUNT_OPTIONS

When this option is enabled, laptop mode tools is allowed to control the mount options for your filesystems. Disabling this will break CONTROL_NOATIME, but it will most probably also break laptop mode itself, as changes to the mount options are crucial for achieving spun-down hard drives.

LM_DIRTY_RATIO

NOLM_DIRTY_RATIO

This option specifies the percentage of system memory that is allowed to contain unwritten modified data when laptop mode is active.
 

LM_DIRTY_BACKGROUND_RATIO

NOLM_DIRTY_BACKGROUND_RATIO

This option specifies the percentage of system memory that is allowed to contain unwritten modified data after the DIRTY_RATIO barrier has been crossed. The effect of this option is that when more than DIRTY_RATIO percent of memory contains modified data, the system will synchronously write back data until only DIRTY_BACKGROUND_RATIO percent of memory contains modified data.

DEF_UPDATE

DEF_XFS_AGE_BUFFER

DEF_XFS_SYNC_INTERVAL

DEF_XFS_BUFD_INTERVAL

DEF_MAX_AGE

These options contain the default (non-laptop-mode) values for some kernel options that are modified when laptop mode is active. You do not normally need to change these, they represent the normal kernel defaults.

XFS_HZ

This option specifies the number of units in a second that is utilized by a 2.4 kernel. If you run a 2.4 kernel with an XFS filesystem on non-Intel hardware, you need to change this option to reflect the kernel "ticks per second" value, which is the kernel variable HZ. Unfortunately this is not exposed anywhere, so you'll have to specify it manually.

LM_SECONDS_BEFORE_SYNC

The number of seconds that laptop mode waits after the disk goes idle before it starts a full sync. This should always be less than your hard disk idle timeout, because otherwise you'll have a sync directly after your drive spins down. Two seconds is usually a good value for this option.
 

XFS_HZ

This option expresses the unit of the XFS tuning parameters. The default is 100. This option is only useful for 2.4 kernels that have a value for HZ that is not 100. In the 2.6 kernel series, the XFS interfaces were modified to always use USER_HZ (which is currently always 100), so for these kernels you do not need to modify this value. Also, on 2.4 kernels the value of HZ is 100 for the most common architectures, so you need only change this value if you use a less common architecture.

/etc/laptop-mode/conf.d/ethernet.conf

The ethernet module allows you to control the behavior of your ethernet devices during AC and battery states.

CONTROL_ETHERNET

Enable this to control various aspects of power savings in the ethernet devices.

BATT_THROTTLE_ETHERNET=1

LM_AC_THROTTLE_ETHERNET=0

NOLM_AC_THROTTLE_ETHERNET=0

These options specify the power states in which you would like to control the ethernet device

THROTTLE_SPEED

Here, you can specify the throttling speed for your ethernet device. The default is "slowest". Valid values are "slowest", "fastest" or the speed of your ethernet device, like 1000. To know the exact speed of your ethernet device, you can use the ethtool tool.

DISABLE_WAKEUP_ON_LAN

This setting controls the option to enable/disable the WoL (Wake On LAN) feature. It permanently disables the WOL feature on the ethernet device. Default is 1. Set it to 0 to enable the WOL feature.

ETHERNET_DEVICES

Specify the list of ethernet devices to control. Defaults to eth0

DISABLE_ETHERNET_ON_BATTERY

Set this to 1 if you want to completely disable your ethernet device when running on battery. Default is 0

/etc/laptop-mode/conf.d/cpufreq.conf

The cpufreq module allows you to control the Linux kernel's CPU frequency scaling settings.

CONTROL_CPU_FREQUENCY

When this option is enabled, laptop mode tools controls your CPU's frequency scaling bounds and the scaling governor. This option is currently only supported on 2.6 kernels.
 

BATT_CPU_MAXFREQ

BATT_CPU_INFREQ

BATT_CPU_GOVERNOR

BATT_CPU_IGNORE_NICE_LOAD

LM_AC_CPU_MAXFREQ

LM_AC_CPU_MINFREQ

LM_AC_CPU_GOVERNOR

LM_AC_CPU_IGNORE_NICE_LOAD

NOLM_AC_CPU_MAXFREQ

NOLM_AC_CPU_MINFREQ

NOLM_AC_CPU_GOVERNOR

NOLM_AC_CPU_IGNORE_NICE_LOAD

These options specify the CPU frequency bounds and scaling governor in the various power states. You can change the MAXFREQ and MINFREQ values to any value listed in

/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies.

In addition, you can use "fastest" and "slowest". The GOVERNOR option controls
the setting for /sys/devices/system/cpu/cpufreq/scaling_governor. The
available options are dependent on the installed kernel. The most
common ones are "conservative", "performance" and "ondemand". The
IGNORE_NICE_LOAD
option controls a setting that is available for the "conservative" and "ondemand"
governors. Set this option to 1 if you want the frequency scaling governor to
not increase the CPU frequency for the sake of low-priority ("nice") background
processes.

CONTROL_CPU_THROTTLING

When this option is enabled, laptop mode tools controls your CPU's throttling level.
It is only useful if your CPU doesn't support frequency scaling.
This option is only supported on some ACPI hardware.

BATT_CPU_THROTTLING

LM_AC_CPU_THROTTLING

NOLM_AC_CPU_THROTTLING

These options specify the throttling level for the CPU in the various power states.
You can change it to any level listed in
/proc/acpi/processor/CPU0/throttling
(use only the number!). In addition, you can use "maximum" (which is the slowest
option), "minimum" (full speed) and "medium" (about halfway).

/etc/laptop-mode/conf.d/sched-smt-power-savings.conf

The sched-smt-power-savings module controls the behavior of the process scheduler
on SMT boxes, when running in battery mode.

CONTROL_SCHED_SMT_POWER_SAVINGS

Set this to 1 to enable power savings in the process scheduler for SMT processors.

/etc/laptop-mode/conf.d/dpms-standby.conf

The dpms-standby module allows you to control the DPMS standby timeouts for
X displays.

CONTROL_DPMS_STANDBY

When this option is enabled, laptop mode will control the DPMS
standby timeout for all X displays on the machine that users have logged on to.
In short, this allows laptop mode to control the time after which your screen
is blanked.

There is one limitation to this feature: the settings are not automatically
applied to new X logons. This can be fixed by configuring the display
manager. For the gdm display manager, configure a PostLogin directory
(usually /etc/gdm/PostLogin or /etc/X11/gdm/PostLogin), and in that directory
create a shell script called Default. In that file, include the command:

( sleep 60 ; /usr/sbin/laptop_mode force ) &

Similar configurations are possible for other window managers. Please consult
your window manager documentation for more information.

BATT_DPMS_STANDBY

LM_AC_DPMS_STANDBY

NOLM_AC_DPMS_STANDBY

These options specify the display standby timeouts for the X displays, in
seconds.

/etc/laptop-mode/conf.d/terminal-blanking.conf

The terminal-blanking module allows you to control the terminal blanking
timeouts for the Linux text console.

CONTROL_TERMINAL

When this option is enabled, laptop mode will control the terminal blanking
settings for Linux's virtual consoles.

TERMINALS

This option should contain a space-separated list of console device files that
should be affected by the terminal blanking settings. Only
one console device file needs to be included, because the settings are shared
between all virtual consoles. By default this setting is set to /dev/tty1.

BATT_TERMINAL_BLANK_MINUTES

LM_AC_TERMINAL_BLANK_MINUTES

NOLM_AC_TERMINAL_BLANK_MINUTES

BATT_TERMINAL_POWERDOWN_MINUTES

LM_AC_TERMINAL_POWERDOWN_MINUTES

NOLM_AC_TERMINAL_POWERDOWN_MINUTES

These options specify the terminal blanking and powerdown timeouts, in
minutes. The allowed ranges are 1-60 minutes, or 0 to disable blanking
or powerdown. The values are cumulative: the powerdown value is counted
from the moment of screen blanking, not from the start of inactivity.

/etc/laptop-mode/conf.d/lcd-brightness.conf

The lcd-brightness module allows you to control the brightness of your LCD
screen.

CONTROL_BRIGHTNESS

When this option is enabled, laptop mode will adjust your LCD screen's
brightness settings, if possible. You must configure the following settings
for this to work.

BATT_BRIGHTNESS_COMMAND

LM_AC_BRIGHTNESS_COMMAND

NOLM_AC_BRIGHTNESS_COMMAND

BRIGHTNESS_OUTPUT

The BRIGHTNESS_COMMAND settings specify commands that should be executed
in order to set the brightness of your LCD. The BRIGHTNESS_OUTPUT setting
specifies where the output of the command will be written. For instance,
if your LCD's brightness is adjusted by writing a numeric value 3 to a file
called /proc/brightness, you should set the command to "echo 3" and the
output file to "/proc/brightness". If your LCD's brightness is adjusted
using a utility like "toshset", you should include the entire toshset
command line as the command, and set the output file to "/dev/null".

/etc/laptop-mode/conf.d/auto-hibernate.conf

The auto-hibernate module allows you to automatically hibernate your computer
when the battery goes critical or when the battery level goes below a certain
threshold.

ENABLE_AUTO_HIBERNATION

When this option is enabled, laptop mode will automatically hibernate your
computer when the battery level reaches a certain configurable threshold. This
feature is only available when ACPI is enabled.

HIBERNATE_COMMAND

This option specifies the command that laptop mode should execute when
auto-hibernation is triggered. Normally, this is set to something like
"/usr/sbin/hibernate".

AUTO_HIBERNATION_BATTERY_CHARGE_PERCENT

The battery level threshold for auto-hibernation, as a percentage of total
battery capacity.

AUTO_HIBERNATION_ON_CRITICAL_BATTERY_LEVEL

When this option is enabled, auto-hibernation will kick in when the battery
reports its state as "critical".

/etc/laptop-mode/conf.d/battery-level-polling.conf

Some battery hardware does not send out proper level change events, or too
infrequent ones. For such hardware, laptop mode tools will not detect that the
battery has reached a critical level. The battery-level-polling module allows
you to use the auto-hibernate module and the other battery level dependent
features of laptop mode tools even when your battery does not send out frequent
ACPI to indicate a change in level.

CONTROL_BATTERY_LEVEL_POLLING

When this option is enabled, laptop mode tools will automatically poll the
battery level every once in a while to see if the levels have changed, and to
see if actions should be taken as a consequence.

/etc/laptop-mode/conf.d/start-stop-programs.conf

The start-stop-programs module allows you to start or stop programs when the
computer switches to a different power state.

CONTROL_START_STOP

If this option is enabled, laptop mode tools will automatically start and stop
daemons or other programs for you. The actual configuration of which daemons
are to be stopped/started is done by placing links to the daemons' init scripts
in the following directories:

/etc/laptop-mode/batt-start

/etc/laptop-mode/batt-stop

/etc/laptop-mode/lm-ac-start

/etc/laptop-mode/lm-ac-stop

/etc/laptop-mode/nolm-ac-start

/etc/laptop-mode/nolm-ac-stop

As you have probably guessed, the directories of the form "X-stop-daemons"
should contain init scripts of daemons that you want stopped in mode X, while
the directories of the form "X-start-daemons" should contain init scripts of
daemons that you want started in mode X. Of course, it is possible to put in
your own handling of modes as well: the only requirement on the scripts in the
directories is that they handle the "start" and "stop" commands, like init
scripts usually do.

The ordering of the script handling is as follows. When a mode is entered, the
actions of the previous mode are undone, in reverse order. This means that if
the previous mode had done "daemon1 stop", "daemon2 stop" and "daemon3 start",
then the undoing actions will be "daemon3 stop", "daemon2 start", "daemon1
start". After that, the stop-scripts for the new mode are called, and then the
start-scripts are called. Please note that there is no detection of
commonalities between modes at this point, i.e., if the mode you're coming
from and the mode you're going to both specify that a daemon "X" should be
stopped, then the daemon will be un-stopped (that is, started) while leaving
the previous mode, and then stopped again.

BATT_STOP

BATT_START

LM_AC_STOP

LM_AC_START

NOLM_AC_STOP

NOLM_AC_START

These options allow you to stop services (through their init scripts) in certain
power states. Specify a space-separated list of service names in these options.
These services are started/stopped together with the files from the directories
mentioned above.

/etc/laptop-mode/conf.d/ac97-powersave.conf

The ac97-powersave module allows you to enable the Intel AC97 integrated audio
power saving mode.

CONTROL_AC97_POWER

If this option is enabled, laptop mode tools will automatically enable the
AC97 power saving settings. The power saving settings are always enabled, not
only on battery power.
Note: On some machines it has been reported that the AC97 power savings triggers
the annoying click sound during power state transitions

/etc/laptop-mode/conf.d/nmi-watchdog.conf

The nmi-watchdog module allows you to enable the NMI Watchdog timer power savings.
Enabling this module lowers down one hw-pmu counter.

CONTROL_NMI_WATCHDOG

If this option is enabled, laptop mode tools will automatically disable the
NMI Watchdog timer when on battery. This module is part of auto modules. Thus enabling
auto modules setting will activate this module automatically.

/etc/laptop-mode/conf.d/pci-aspm.conf

The pcie-aspm module allows you to enable the PCI Express (PCIe) Active State
Power Management (ASPM).

CONTROL_PCI_ASPM

If this option is enabled, laptop mode tools will enable PCI ASPM powersave
mode when on battery. This module is part of auto modules. Thus enabling
auto modules setting will activate this module automatically. PCIe ASPM may
require that the pcie_aspm=force kernel option is enabled.

/etc/laptop-mode/conf.d/runtime-pm.conf

The runtime-pm module allows you to enable the Runtime Power Management
framework for the Linux kernel.

CONTROL_RUNTIME_PM

If this option is enabled, laptop mode tools will automatically enable the
Kernel's Runtime Power Management settings. The power saving settings are always
enabled, not only on battery power.

/etc/laptop-mode/conf.d/intel-hda-powersave.conf

The intel-hda-powersave module allows you to enable the Intel HDA integrated
audio power saving mode.

CONTROL_INTEL_HDA_POWER

If this option is enabled, laptop mode tools will automatically enable the
Intel HDA power saving settings. The power saving settings are always enabled,
not only on battery power.

/etc/laptop-mode/conf.d/configuration-file-control.conf

The configuration-file-control module allows you to switch between different
configuration files when the computer is in different power states.

The primary use for this feature is for controlling the configuration files
of syslog daemons. Syslog daemons have a tendency to sync their log files when
entries are written to them. This causes disks to spin up, which is not very
nice when you're trying to save power. The syslog.conf configuration file
can be tweaked so that syslogd will not sync a given file, by prepending
the log file name with a dash, like this:

mail.* -/var/log/mail/mail.log

Note:
This feature will NOT work if CONTROL_SYSLOG_CONF is set in laptop-mode.conf.
To start using this feature, remove the CONTROL_SYSLOG_CONF section in
laptop-mode.conf, and then restart the laptop-mode-tools service. The new config
files have different names than the old ones, and settings are NOT
migrated. You will have to do this manually.

CONTROL_CONFIG_FILES

If this option is enabled, laptop mode tools will use the following options to
switch configuration files depending on the power state.

CONFIG_FILES

This option should contain a space-separated list of configuration files that
should be switched around depending on the power state.

For each configuration file, the specific configuration files will be named as follows:

.I <conffile>-nolm-ac

<conffile>-lm-ac

<conffile>-batt

The first file will be used when the system is on AC power and laptop mode
is not active. The second file will be used when the system is on AC power and
laptop mode is active. The third file will be used when the system is on
battery power.

When the laptop mode tools service is enabled, it will replace the
configuration files with a symlink to one of the three state-based
configuration files. The original configuration file will be saved as
<config file>.lmbackup, and it will be restored when the laptop mode tools
service is disabled.

When you add files to this list, make sure to also add the appropriate
programs and services to the configuration settings below.

You can create the alternate configuration files yourself. If you don't, they
will be created by laptop mode tools the next time it is restarted. To force
the files to be created, run the laptop-mode service init script with the
"restart" parameter.

CONFIG_FILE_SIGNAL_PROGRAMS

This option should contain a space-separated list of programs that should be
signalled after the config files have been switched around. This only works for
programs that respond to the SIGHUP signal by reloading their configuration
files.

CONFIG_FILE_RELOAD_SERVICES

This option should contain a space-separated list of services which should be
reloaded after the config files have been switched around.

/etc/laptop-mode/conf.d/wireless-power.conf

The wireless-power module allows you to alter the power management settings
for wireless network adapters that support the iwconfig "power" option. This
module is not usable for Intel network adapters that use the iwlwifi or ipw
drivers, they are supported by separate modules described below.

CONTROL_WIRELESS_POWER_SAVING

If this option is enabled, laptop mode tools will set the wireless power
saving mode settings based on the power state.

WIRELESS_AC_POWER_SAVING

WIRELESS_BATT_POWER_SAVING

These settings define the power saving modes on AC and on battery. The allowed
values are 0 (to disable power saving mode) and 1 (to enable power saving mode).

/etc/laptop-mode/conf.d/wireless-ipw-power.conf

The wireless-ipw-power module allows you to alter the power management settings
for Intel PRO/Wireless 3945, 2100 and 2200 wireless network adapters. This
module is intended for use with the ipw3945, ipw2100, ipw2200 drivers, not with
the iwlwifi drivers.

CONTROL_IPW_POWER

If this option is enabled, laptop mode tools will set the wireless power
management settings based on the power state.

IPW3945_AC_POWER

IPW3945_BATT_POWER

These settings define the power management levels for the ipw3945 driver. The
defaults are 6 for AC, and 7 for battery mode. The allowed values are 1 (highest
power) to 5 (lowest power), 6 (AC mode, full power) and 7 (battery mode, lowest
power).

IPW2100_AC_POWER

IPW2100_BATT_POWER

These settings define the power management levels for the ipw2100 driver. The
defaults are 0 for AC mode and 5 for battery mode.

/etc/laptop-mode/conf.d/wireless-iwl-power.conf

The wireless-iwl-power module allows you to alter the power management settings
for Intel PRO/Wireless 3945 and Intel WiFi Link 4965 wireless network adapters.
This module is intended for use with the iwlwifi drivers, not with the old ipw
drivers.

CONTROL_IWL_POWER

If this option is enabled, laptop mode tools will set the wireless power
management settings based on the power state.

IWL_AC_POWER

IWL_BATT_POWER

These settings define the power management levels on AC and on battery. The
defaults are 0 for AC, and 3 for battery mode. The allowed values are 0 (highest
power) to 5 (lowest power), 6 (AC mode, full power) and 7 (battery mode, lowest
power).

/etc/laptop-mode/conf.d/exec-commands.conf

There can be many odd machines and many power savings settings, that laptop-mode-tools currently does not cover. If you run into a similar power saving problem, where you do not have a laptop-mode-tools module for it, you can use the exec-commands module to trigger the command during power state changes. Please do contribute back the power saving item as a module to the upstream developers.

CONTROL_EXEC_COMMANDS

Set this to 0 to disable execution of custom commands during power state changes. Default is auto.

BATT_EXEC_COMMAND_0=

BATT_EXEC_COMMAND_1=

LM_AC_EXEC_COMMAND_0=

LM_AC_EXEC_COMMAND_1=

NOLM_AC_EXEC_COMMAND_0=

NOLM_AC_EXEC_COMMAND_1=

Here you can specify your custom command that will need to be executed. The numbers can grow upto 9. The command needs to be specified in double quotes

/etc/laptop-mode/conf.d/usb-autosuspend.conf

The usb-autosuspend module allows you to automatically enable the Linux
kernel's USB autosuspend feature for all USB devices.

CONTROL_USB_AUTOSUSPEND

If this option is enabled, laptop mode tools will automatically enable the
USB autosuspend feature for all devices. The USB autosuspend feature will always
be enabled, not only on battery power.

AUTOSUSPEND_USBID_BLACKLIST

Here, you can specify the list of USB IDs that should not use autosuspend.
Use lsusb to find out the IDs of your USB devices.
Example: AUTOSUSPEND_USBID_BLACKLIST="046d:c025 0123:abcd"

/etc/laptop-mode/conf.d/eee-superhe.conf

The eee-superhe module allows you to control the CPU frequency scalling on the
EEE PC. It requires the eeepc_laptop kernel module to be loaded.

CONTROL_SUPERHE

It this option is enabled, laptop mode tools will automatically control the FSB
speed on the EEE PC.

BATT_SUPERHE

LM_AC_SUPERHE

NOLM_AC_SUPERHE

These settings define the power management levels on AC and on battery. The
defaults are 0 for LM_AC and NOLM_AC, and 2 for battery mode.

/etc/laptop-mode/conf.d/hal-polling.conf

The hal-polling module allows you to control the polling of CD/DVD drives
by HAL. The polling is needed for some drives to detect inserted CDs, but it
uses a considerable amount of power. Enable this module to disable the polling,
but only if our drive doesn't need it, or if you are willing to mount CDs
manually in exchange for the power saving.

CONTROL_HAL_POLLING

If this option is enabled, laptop mode tools will control the HAL polling
behaviour.

BATT_DISABLE_HAL_POLLING

AC_DISABLE_HAL_POLLING

These settings define the polling behaviour on AC and on battery. To disable
polling, set the options to 1, to enable, set them to 0.

HAL_POLLING_DEVICES

This setting defines for which devices the polling behaviour will be altered.
It should contain a space separated list of devices.

/etc/laptop-mode/conf.d/bluetooth.conf

The bluetooth module allows you to enable/disable bluetooth depending on the
power state.

CONTROL_BLUETOOTH

If this option is enabled, laptop mode tools will enable/disable bluetooth
when the power state changes.

BATT_ENABLE_BLUETOOTH

AC_ENABLE_BLUETOOTH

These settings define whether bluetooth is enabled on AC and on battery. To
disable bluetooth, set the options to 0, to enable, set them to 1.

BLUETOOTH_INTERFACES

This setting defines the interfaces the bluetooth module will control. It
should contain a space separated list of interfaces. (Note that you probably
have only one bluetooth interface, and it will probably be named "hci0".)

/etc/laptop-mode/conf.d/intel-sata-powermgmt.conf

The intel-sata-powermgmt module allows you to enable the power saving mode for
Intel AHCI compliant SATA controllers. This power saving mode is also known as
Aggressive Link Power Management (ALPM).

CONTROL_INTEL_SATA_POWER

If this option is enabled, laptop mode tools will automatically enable the
Intel SATA controller power saving settings. The power saving settings are
always enabled, not only on battery power.

BATT_ACTIVATE_SATA_POWER=1

LM_AC_ACTIVATE_SATA_POWER=0

NOLM_AC_ACTIVATE_SATA_POWER=0

These settings control the behavior of the SATA devices under AC and battery power states

/etc/laptop-mode/conf.d/sched-mc-power-savings.conf

The sched-mc-power-savings module allows you to tune the Linux kernel process
scheduler to optimize for power usage on multi-core and multi-processor
computers.

CONTROL_SCHED_MC_POWER_SAVINGS

If this option is enabled, laptop mode tools will automatically configure the
kernel process scheduler to optimize for power usage on multi-core and
multi-processor computers. The optimizations will only be enabled in battery
mode.

/etc/laptop-mode/conf.d/video-out.conf

The video-out module allows you to selectively disable video outputs depending
on the power status. This works only for video hardware that supports xrandr.

CONTROL_VIDEO_OUTPUTS

If this option is enabled, laptop mode tools will automatically disable
the configured video outputs.

BATT_DISABLE_VIDEO_OUTPUTS

LM_AC_DISABLE_VIDEO_OUTPUTS

NOLM_AC_DISABLE_VIDEO_OUTPUTS

These settings define which video outputs are to be disabled in which power
state. The format is a space-separated list of outputs. The allowed names of the
outputs depend on what the video hardware supports, they can be found by running
the "xrandr" command.

SEE ALSO

laptop_mode(8).

lm-profiler(8).

hdparm(8).

AUTHOR

This manual page was written by Bart Samwel (bart@samwel.tk).
Permission is granted to copy, distribute and/or modify this document under
the terms of the GNU General Public License, Version 2 any
later version published by the Free Software Foundation.