Load the www device when using groff; provide a fallback for groff's MTO macro that formats email addresses.
NAMEflashrom - detect, read, write, verify and erase flash chips
SYNOPSISflashrom [-h|-R|-L|-z|-p <programmername>[:<parameters>]
[-E|-r <file>|-w <file>|-v <file>] [-c <chipname>]
[-l <file> [-i <image>]] [-n] [-f]]
[-V[V[V]]] [-o <logfile>]
DESCRIPTIONflashrom is a utility for detecting, reading, writing, verifying and erasing flash chips. It's often used to flash BIOS/EFI/coreboot/firmware images in-system using a supported mainboard. However, it also supports various external PCI/USB/parallel-port/serial-port based devices which can program flash chips, including some network cards (NICs), SATA/IDE controller cards, graphics cards, the Bus Pirate device, various FTDI FT2232/FT4232H/FT232H based USB devices, and more.
It supports a wide range of DIP32, PLCC32, DIP8, SO8/SOIC8, TSOP32, TSOP40, TSOP48, and BGA chips, which use various protocols such as LPC, FWH, parallel flash, or SPI.
OPTIONSIMPORTANT: Please note that the command line interface for flashrom will change before flashrom 1.0. Do not use flashrom in scripts or other automated tools without checking that your flashrom version won't interpret options in a different way.
You can specify one of -h, -R, -L, -z, -E, -r, -w, -v or no operation. If no operation is specified, flashrom will only probe for flash chips. It is recommended that if you try flashrom the first time on a system, you run it in probe-only mode and check the output. Also you are advised to make a backup of your current ROM contents with -r before you try to write a new image. All operations involving any chip access (probe/read/write/...) require the -p/--programmer option to be used (please see below).
- -r, --read <file>
- Read flash ROM contents and save them into the given <file>. If the file already exists, it will be overwritten.
- -w, --write <file>
into flash ROM. This will first automatically
the chip, then write to it.
In the process the chip is also read several times. First an in-memory backup is made for disaster recovery and to be able to skip regions that are already equal to the image file. This copy is updated along with the write operation. In case of erase errors it is even re-read completely. After writing has finished and if verification is enabled, the whole flash chip is read out and compared with the input image.
- -n, --noverify
Skip the automatic verification of flash ROM contents after writing. Using this
recommended, you should only use it if you know what you are doing and if you
feel that the time for verification takes too long.
Typical usage is: flashrom -p prog -n -w <file>
This option is only useful in combination with --write.
- -v, --verify <file>
- Verify the flash ROM contents against the given <file>.
- -E, --erase
- Erase the flash ROM chip.
- -V, --verbose
- More verbose output. This option can be supplied multiple times (max. 3 times, i.e. -VVV) for even more debug output.
- -c, --chip <chipname>
- Probe only for the specified flash ROM chip. This option takes the chip name as printed by flashrom -L without the vendor name as parameter. Please note that the chip name is case sensitive.
- -f, --force
Force one or more of the following actions:
* Force chip read and pretend the chip is there.
* Force chip access even if the chip is bigger than the maximum supported size for the flash bus.
* Force erase even if erase is known bad.
* Force write even if write is known bad.
- -l, --layout <file>
Read ROM layout from
flashrom supports ROM layouts. This allows you to flash certain parts of the flash chip only. A ROM layout file contains multiple lines with the following syntax:
startaddr and endaddr are hexadecimal addresses within the ROM file and do not refer to any physical address. Please note that using a 0x prefix for those hexadecimal numbers is not necessary, but you can't specify decimal/octal numbers. imagename is an arbitrary name for the region/image from startaddr to endaddr (both addresses included).
If you only want to update the image named normal in a ROM based on the layout above, run
flashrom -p prog --layout rom.layout --image normal -w some.rom
To update only the images named normal and fallback, run:
flashrom -p prog -l rom.layout -i normal -i fallback -w some.rom
Overlapping sections are not supported.
- -i, --image <imagename>
- Only flash region/image <imagename> from flash layout.
- -L, --list-supported
List the flash chips, chipsets, mainboards, and external programmers
(including PCI, USB, parallel port, and serial port based devices)
supported by flashrom.
There are many unlisted boards which will work out of the box, without special support in flashrom. Please let us know if you can verify that other boards work or do not work out of the box.
IMPORTANT: For verification you have to test an ERASE and/or WRITE operation, so make sure you only do that if you have proper means to recover from failure!
- -z, --list-supported-wiki
- Same as --list-supported, but outputs the supported hardware in MediaWiki syntax, so that it can be easily pasted into the Please note that MediaWiki output is not compiled in by default.
- -p, --programmer <name>[:parameter[,parameter[,parameter]]]
Specify the programmer device. This is mandatory for all operations
involving any chip access (probe/read/write/...). Currently supported are:
* internal (for in-system flashing in the mainboard)
* dummy (virtual programmer for testing flashrom)
* nic3com (for flash ROMs on 3COM network cards)
* nicrealtek (for flash ROMs on Realtek and SMC 1211 network cards)
* nicnatsemi (for flash ROMs on National Semiconductor DP838* network cards)
* nicintel (for parallel flash ROMs on Intel 10/100Mbit network cards)
* gfxnvidia (for flash ROMs on NVIDIA graphics cards)
* drkaiser (for flash ROMs on Dr. Kaiser PC-Waechter PCI cards)
* satasii (for flash ROMs on Silicon Image SATA/IDE controllers)
* satamv (for flash ROMs on Marvell SATA controllers)
* atahpt (for flash ROMs on Highpoint ATA/RAID controllers)
* atavia (for flash ROMs on VIA VT6421A SATA controllers)
* atapromise (for flash ROMs on Promise PDC2026x ATA/RAID controllers)
* it8212 (for flash ROMs on ITE IT8212F ATA/RAID controller)
* ft2232_spi (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family based USB SPI programmer).
* serprog (for flash ROMs attached to a programmer speaking serprog, including some Arduino-based devices).
* buspirate_spi (for SPI flash ROMs attached to a Bus Pirate)
* dediprog (for SPI flash ROMs attached to a Dediprog SF100)
* rayer_spi (for SPI flash ROMs attached to a parallel port by one of various cable types)
* pony_spi (for SPI flash ROMs attached to a SI-Prog serial port bitbanging adapter)
* nicintel_spi (for SPI flash ROMs on Intel Gigabit network cards)
* ogp_spi (for SPI flash ROMs on Open Graphics Project graphics card)
* linux_spi (for SPI flash ROMs accessible via /dev/spidevX.Y on Linux)
* usbblaster_spi (for SPI flash ROMs attached to an Altera USB-Blaster compatible cable)
* nicintel_eeprom (for SPI EEPROMs on Intel Gigabit network cards)
* mstarddc_spi (for SPI flash ROMs accessible through DDC in MSTAR-equipped displays)
* pickit2_spi (for SPI flash ROMs accessible via Microchip PICkit2)
* ch341a_spi (for SPI flash ROMs attached to WCH CH341A)
Some programmers have optional or mandatory parameters which are described in detail in the PROGRAMMER-SPECIFIC INFORMATION section. Support for some programmers can be disabled at compile time. flashrom -h lists all supported programmers.
- -h, --help
- Show a help text and exit.
- -o, --output <logfile>
- Save the full debug log to <logfile>. If the file already exists, it will be overwritten. This is the recommended way to gather logs from flashrom because they will be verbose even if the on-screen messages are not verbose and don't require output redirection.
- -R, --version
- Show version information and exit.
PROGRAMMER-SPECIFIC INFORMATIONSome programmer drivers accept further parameters to set programmer-specific parameters. These parameters are separated from the programmer name by a colon. While some programmers take arguments at fixed positions, other programmers use a key/value interface in which the key and value is separated by an equal sign and different pairs are separated by a comma or a colon.
- Board Enables
Some mainboards require to run mainboard specific code to enable flash erase and write support (and probe support on old systems with parallel flash). The mainboard brand and model (if it requires specific code) is usually autodetected using one of the following mechanisms: If your system is running coreboot, the mainboard type is determined from the coreboot table. Otherwise, the mainboard is detected by examining the onboard PCI devices and possibly DMI info. If PCI and DMI do not contain information to uniquely identify the mainboard (which is the exception), or if you want to override the detected mainboard model, you can specify the mainboard using the
flashrom -p internal:mainboard=<vendor>:<board> syntax.
See the 'Known boards' or 'Known laptops' section in the output of 'flashrom -L' for a list of boards which require the specification of the board name, if no coreboot table is found.
Some of these board-specific flash enabling functions (called board enables) in flashrom have not yet been tested. If your mainboard is detected needing an untested board enable function, a warning message is printed and the board enable is not executed, because a wrong board enable function might cause the system to behave erratically, as board enable functions touch the low-level internals of a mainboard. Not executing a board enable function (if one is needed) might cause detection or erasing failure. If your board protects only part of the flash (commonly the top end, called boot block), flashrom might encounter an error only after erasing the unprotected part, so running without the board-enable function might be dangerous for erase and write (which includes erase).
The suggested procedure for a mainboard with untested board specific code is to first try to probe the ROM (just invoke flashrom and check that it detects your flash chip type) without running the board enable code (i.e. without any parameters). If it finds your chip, fine. Otherwise, retry probing your chip with the board-enable code running, using
flashrom -p internal:boardenable=force
If your chip is still not detected, the board enable code seems to be broken or the flash chip unsupported. Otherwise, make a backup of your current ROM contents (using -r) and store it to a medium outside of your computer, like a USB drive or a network share. If you needed to run the board enable code already for probing, use it for reading too. If reading succeeds and the contens of the read file look legit you can try to write the new image. You should enable the board enable code in any case now, as it has been written because it is known that writing/erasing without the board enable is going to fail. In any case (success or failure), please report to the flashrom mailing list, see below.
On systems running coreboot, flashrom checks whether the desired image matches your mainboard. This needs some special board ID to be present in the image. If flashrom detects that the image you want to write and the current board do not match, it will refuse to write the image unless you specify
flashrom -p internal:boardmismatch=force
- ITE IT87 Super I/O
If your mainboard is manufactured by GIGABYTE and supports DualBIOS it is very likely that it uses an ITE IT87 series Super I/O to switch between the two flash chips. Only one of them can be accessed at a time and you can manually select which one to use with the
flashrom -p internal:dualbiosindex=chip
syntax where chip is the index of the chip to use (0 = main, 1 = backup). You can check which one is currently selected by leaving out the chip parameter.
If your mainboard uses an ITE IT87 series Super I/O for LPC<->SPI flash bus translation, flashrom should autodetect that configuration. If you want to set the I/O base port of the IT87 series SPI controller manually instead of using the value provided by the BIOS, use the
flashrom -p internal:it87spiport=portnum
syntax where portnum is the I/O port number (must be a multiple of 8). In the unlikely case flashrom doesn't detect an active IT87 LPC<->SPI bridge, please send a bug report so we can diagnose the problem.
- AMD chipsets
Beginning with the SB700 chipset there is an integrated microcontroller (IMC) based on the 8051 embedded in every AMD southbridge. Its firmware resides in the same flash chip as the host's which makes writing to the flash risky if the IMC is active. Flashrom tries to temporarily disable the IMC but even then changing the contents of the flash can have unwanted effects: when the IMC continues (at the latest after a reboot) it will continue executing code from the flash. If the code was removed or changed in an unfortunate way it is unpredictable what the IMC will do. Therefore, if flashrom detects an active IMC it will disable write support unless the user forces it with the
flashrom -p internal:amd_imc_force=yes
syntax. The user is responsible for supplying a suitable image or leaving out the IMC region with the help of a layout file. This limitation might be removed in the future when we understand the details better and have received enough feedback from users. Please report the outcome if you had to use this option to write a chip.
An optional spispeed parameter specifies the frequency of the SPI bus where applicable (i.e. SB600 or later with an SPI flash chip directly attached to the chipset). Syntax is
flashrom -p internal:spispeed=frequency
where frequency can be '16.5 MHz', '22 MHz', '33 MHz', '66 MHz', '100 MHZ', or '800 kHz'. Support of individual frequencies depends on the generation of the chipset:
* SB6xx, SB7xx, SP5xxx: from 16.5 MHz up to and including 33 MHz
* SB8xx, SB9xx, Hudson: from 16.5 MHz up to and including 66 MHz
* Yangtze (with SPI 100 engine as found in Kabini and Tamesh): all of them
The default is to use 16.5 MHz and disable Fast Reads.
- Intel chipsets
If you have an Intel chipset with an ICH8 or later southbridge with SPI flash attached, and if a valid descriptor was written to it (e.g. by the vendor), the chipset provides an alternative way to access the flash chip(s) named Hardware Sequencing. It is much simpler than the normal access method (called Software Sequencing), but does not allow the software to choose the SPI commands to be sent. You can use the
flashrom -p internal:ich_spi_mode=value
syntax where value can be auto, swseq or hwseq. By default (or when setting ich_spi_mode=auto) the module tries to use swseq and only activates hwseq if need be (e.g. if important opcodes are inaccessible due to lockdown; or if more than one flash chip is attached). The other options (swseq, hwseq) select the respective mode (if possible).
ICH8 and later southbridges may also have locked address ranges of different kinds if a valid descriptor was written to it. The flash address space is then partitioned in multiple so called "Flash Regions" containing the host firmware, the ME firmware and so on respectively. The flash descriptor can also specify up to 5 so called "Protected Regions", which are freely chosen address ranges independent from the aforementioned "Flash Regions". All of them can be write and/or read protected individually. If flashrom detects such a lock it will disable write support unless the user forces it with the
flashrom -p internal:ich_spi_force=yes
syntax. If this leads to erase or write accesses to the flash it would most probably bring it into an inconsistent and unbootable state and we will not provide any support in such a case.
If you have an Intel chipset with an ICH2 or later southbridge and if you want to set specific IDSEL values for a non-default flash chip or an embedded controller (EC), you can use the
flashrom -p internal:fwh_idsel=value
syntax where value is the 48-bit hexadecimal raw value to be written in the IDSEL registers of the Intel southbridge. The upper 32 bits use one hex digit each per 512 kB range between 0xffc00000 and 0xffffffff, and the lower 16 bits use one hex digit each per 1024 kB range between 0xff400000 and 0xff7fffff. The rightmost hex digit corresponds with the lowest address range. All address ranges have a corresponding sister range 4 MB below with identical IDSEL settings. The default value for ICH7 is given in the example below.
Example: flashrom -p internal:fwh_idsel=0x001122334567
Using flashrom on laptops is dangerous and may easily make your hardware unusable (see also the BUGS section). The embedded controller (EC) in these machines often interacts badly with flashing. More information is For example the EC firmware sometimes resides on the same flash chip as the host firmware. While flashrom tries to change the contents of that memory the EC might need to fetch new instructions or data from it and could stop working correctly. Probing for and reading from the chip may also irritate your EC and cause fan failure, backlight failure, sudden poweroff, and other nasty effects. flashrom will attempt to detect if it is running on a laptop and abort immediately for safety reasons if it clearly identifies the host computer as one. If you want to proceed anyway at your own risk, use
flashrom -p internal:laptop=force_I_want_a_brick
We will not help you if you force flashing on a laptop because this is a really dumb idea.
You have been warned.
Currently we rely on the chassis type encoded in the DMI/SMBIOS data to detect laptops. Some vendors did not implement those bits correctly or set them to generic and/or dummy values. flashrom will then issue a warning and bail out like above. In this case you can use
flashrom -p internal:laptop=this_is_not_a_laptop
to tell flashrom (at your own risk) that it is not running on a laptop.
The dummy programmer operates on a buffer in memory only. It provides a safe and fast way to test various
aspects of flashrom and is mainly used in development and while debugging.
It is able to emulate some chips to a certain degree (basic
identify/read/erase/write operations work).
An optional parameter specifies the bus types it should support. For that you have to use the
flashrom -p dummy:bus=[type[+type[+type]]]
syntax where type can be parallel, lpc, fwh, spi in any order. If you specify bus without type, all buses will be disabled. If you do not specify bus, all buses will be enabled.
Example: flashrom -p dummy:bus=lpc+fwh
The dummy programmer supports flash chip emulation for automated self-tests without hardware access. If you want to emulate a flash chip, use the
flashrom -p dummy:emulate=chip
syntax where chip is one of the following chips (please specify only the chip name, not the vendor):
* ST M25P10.RES SPI flash chip (128 kB, RES, page write)
* SST SST25VF040.REMS SPI flash chip (512 kB, REMS, byte write)
* SST SST25VF032B SPI flash chip (4096 kB, RDID, AAI write)
* Macronix MX25L6436 SPI flash chip (8192 kB, RDID, SFDP)
Example: flashrom -p dummy:emulate=SST25VF040.REMS
- Persistent images
If you use flash chip emulation, flash image persistence is available as well by using the
flashrom -p dummy:emulate=chip,image=image.rom
syntax where image.rom is the file where the simulated chip contents are read on flashrom startup and where the chip contents on flashrom shutdown are written to.
Example: flashrom -p dummy:emulate=M25P10.RES,image=dummy.bin
- SPI write chunk size
If you use SPI flash chip emulation for a chip which supports SPI page write with the default opcode, you can set the maximum allowed write chunk size with the
flashrom -p dummy:emulate=chip,spi_write_256_chunksize=size
syntax where size is the number of bytes (min. 1, max. 256).
flashrom -p dummy:emulate=M25P10.RES,spi_write_256_chunksize=5
- SPI blacklist
To simulate a programmer which refuses to send certain SPI commands to the flash chip, you can specify a blacklist of SPI commands with the
flashrom -p dummy:spi_blacklist=commandlist
syntax where commandlist is a list of two-digit hexadecimal representations of SPI commands. If commandlist is e.g. 0302, flashrom will behave as if the SPI controller refuses to run command 0x03 (READ) and command 0x02 (WRITE). commandlist may be up to 512 characters (256 commands) long. Implementation note: flashrom will detect an error during command execution.
- SPI ignorelist
To simulate a flash chip which ignores (doesn't support) certain SPI commands, you can specify an ignorelist of SPI commands with the
flashrom -p dummy:spi_ignorelist=commandlist
syntax where commandlist is a list of two-digit hexadecimal representations of SPI commands. If commandlist is e.g. 0302, the emulated flash chip will ignore command 0x03 (READ) and command 0x02 (WRITE). commandlist may be up to 512 characters (256 commands) long. Implementation note: flashrom won't detect an error during command execution.
- SPI status register
You can specify the initial content of the chip's status register with the
flashrom -p dummy:spi_status=content
syntax where content is an 8-bit hexadecimal value.
These programmers have an option to specify the PCI address of the card
your want to use, which must be specified if more than one card supported
by the selected programmer is installed in your system. The syntax is
flashrom -p xxxx:pci=bb:dd.f,
where xxxx is the name of the programmer, bb is the PCI bus number, dd is the PCI device number, and f is the PCI function number of the desired device.
Example: flashrom -p nic3com:pci=05:04.0
Due to the mysterious address handling of the VIA VT6421A controller the user can specify an offset with the
flashrom -p atavia:offset=addr
syntax where addr will be interpreted as usual (leading 0x (0) for hexadecimal (octal) values, or else decimal). For more information please see
- This programmer is currently limited to 32 kB, regardless of the actual size of the flash chip. This stems from the fact that, on the tested device (a Promise Ultra100), not all of the chip's address lines were actually connected. You may use this programmer to flash firmware updates, since these are only 16 kB in size (padding to 32 kB is required).
- This is the first programmer module in flashrom that does not provide access to NOR flash chips but EEPROMs mounted on gigabit Ethernet cards based on Intel's 82580 NIC. Because EEPROMs normally do not announce their size nor allow themselves to be identified, the controller relies on correct size values written to predefined addresses within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an unprogrammed EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: Atmel AT25128, AT25256, Micron (ST) M95128, M95256 and OnSemi (Catalyst) CAT25CS128.
This module supports various programmers based on FTDI FT2232/FT4232H/FT232H chips including the DLP Design
DLP-USB1232H, openbiosprog-spi, Amontec JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster,
Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, OpenMoko Neo1973 Debug board (V2+), TIAO/DIYGADGET USB
Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2.
An optional parameter specifies the controller type and channel/interface/port it should support. For that you have to use the
flashrom -p ft2232_spi:type=model,port=interface
syntax where model can be 2232H, 4232H, 232H, jtagkey, busblaster, openmoko, arm-usb-tiny, arm-usb-tiny-h, arm-usb-ocd, arm-usb-ocd-hgoogle-servo-v2-legacy and interface can be A, B, C, or D. The default model is 4232H and the default interface is A.
If there is more than one ft2232_spi-compatible device connected, you can select which one should be used by specifying its serial number with the
flashrom -p ft2232_spi:serial=number
syntax where number is the serial number of the device (which can be found for example in the output of lsusb -v).
All models supported by the ft2232_spi driver can configure the SPI clock rate by setting a divisor. The expressible divisors are all even numbers between 2 and 2^17 (=131072) resulting in SPI clock frequencies of 6 MHz down to about 92 Hz for 12 MHz inputs. The default divisor is set to 2, but you can use another one by specifying the optional divisor parameter with the
flashrom -p ft2232_spi:divisor=div
This module supports all programmers speaking the serprog protocol. This includes some Arduino-based devices
as well as various programmers by Urja Rannikko, Juhana Helovuo, Stefan Tauner, Chi Zhang and many others.
A mandatory parameter specifies either a serial device (and baud rate) or an IP/port combination for communicating with the programmer. The device/baud combination has to start with dev= and separate the optional baud rate with a colon. For example
flashrom -p serprog:dev=/dev/ttyS0:115200
If no baud rate is given the default values by the operating system/hardware will be used. For IP connections you have to use the
flashrom -p serprog:ip=ipaddr:port
syntax. In case the device supports it, you can set the SPI clock frequency with the optional spispeed parameter. The frequency is parsed as hertz, unless an M, or k suffix is given, then megahertz or kilohertz are used respectively. Example that sets the frequency to 2 MHz:
flashrom -p serprog:dev=/dev/device:baud,spispeed=2M
More information about serprog is available in serprog-protocol.txt in the source distribution.
parameter specifies the Bus Pirate device node and an optional
parameter specifies the frequency of the SPI bus. The parameter
delimiter is a comma. Syntax is
flashrom -p buspirate_spi:dev=/dev/device,spispeed=frequency
where frequency can be 30k, 125k, 250k, 1M, 2M, 2.6M, 4M or 8M (in Hz). The default is the maximum frequency of 8 MHz.
An optional pullups parameter specifies the use of the Bus Pirate internal pull-up resistors. This may be needed if you are working with a flash ROM chip that you have physically removed from the board. Syntax is
flashrom -p buspirate_spi:pullups=state
where state can be on or off. More information about the Bus Pirate pull-up resistors and their purpose is available Only the external supply voltage (Vpu) is supported as of this writing.
parameter specifies the voltage the PICkit2 should use. The default unit is Volt if no unit is specified.
You can use
mV, millivolt, V or Volt
as unit specifier. Syntax is
flashrom -p pickit2_spi:voltage=value
where value can be 0V, 1.8V, 2.5V, 3.5V or the equivalent in mV.
An optional spispeed parameter specifies the frequency of the SPI bus. Syntax is
flashrom -p pickit2_spi:spispeed=frequency
where frequency can be 250k, 333k, 500k or 1M (in Hz). The default is a frequency of 1 MHz.
parameter specifies the voltage the Dediprog should use. The default unit is
Volt if no unit is specified. You can use
mV, milliVolt, V or Volt
as unit specifier. Syntax is
flashrom -p dediprog:voltage=value
where value can be 0V, 1.8V, 2.5V, 3.5V or the equivalent in mV.
An optional device parameter specifies which of multiple connected Dediprog devices should be used. Please be aware that the order depends on libusb's usb_get_busses() function and that the numbering starts at 0. Usage example to select the second device:
flashrom -p dediprog:device=1
An optional spispeed parameter specifies the frequency of the SPI bus. The firmware on the device needs to be 5.0.0 or newer. Syntax is
flashrom -p dediprog:spispeed=frequency
where frequency can be 375k, 750k, 1.5M, 2.18M, 3M, 8M, 12M or 24M (in Hz). The default is a frequency of 12 MHz.
An optional target parameter specifies which target chip should be used. Syntax is
flashrom -p dediprog:target=value
where value can be 1 or 2 to select target chip 1 or 2 respectively. The default is target chip 1.
The default I/O base address used for the parallel port is 0x378 and you can use
parameter to specify an alternate base I/O address with the
flashrom -p rayer_spi:iobase=baseaddr
syntax where baseaddr is base I/O port address of the parallel port, which must be a multiple of four. Make sure to not forget the "0x" prefix for hexadecimal port addresses.
The default cable type is the RayeR cable. You can use the optional type parameter to specify the cable type with the
flashrom -p rayer_spi:type=model
syntax where model can be rayer for the RayeR cable, byteblastermv for the Altera ByteBlasterMV, stk200 for the Atmel STK200/300, wiggler for the Macraigor Wiggler, xilinx for the Xilinx Parallel Cable III (DLC 5), or spi_tt for SPI Tiny Tools-compatible hardware.
More information about the RayeR hardware is available at The Altera ByteBlasterMV datasheet can be obtained from For more information about the Macraigor Wiggler see The schematic of the Xilinx DLC 5 was published in
The serial port (like /dev/ttyS0, /dev/ttyUSB0 on Linux or COM3 on windows) is
specified using the mandatory
parameter. The adapter type is selectable between SI-Prog (used for
SPI devices with PonyProg 2000) or a custom made serial bitbanging programmer
named "serbang". The optional
parameter accepts the values "si_prog" (default) or "serbang".
Information about the SI-Prog adapter can be found at
An example call to flashrom is
flashrom -p pony_spi:dev=/dev/ttyS0,type=serbang
Please note that while USB-to-serial adapters work under certain circumstances, this slows down operation considerably.
The flash ROM chip to access must be specified with the
flashrom -p ogp_spi:rom=name
Where name is either cprom or s3 for the configuration ROM and bprom or bios for the BIOS ROM. If more than one card supported by the ogp_spi programmer is installed in your system, you have to specify the PCI address of the card you want to use with the pci= parameter as explained in the nic3com et al. section above.
You have to specify the SPI controller to use with the
flashrom -p linux_spi:dev=/dev/spidevX.Y
syntax where /dev/spidevX.Y is the Linux device node for your SPI controller.
In case the device supports it, you can set the SPI clock frequency with the optional spispeed parameter. The frequency is parsed as kilohertz. Example that sets the frequency to 8 MHz:
flashrom -p linux_spi:dev=/dev/spidevX.Y,spispeed=8000
Please note that the linux_spi driver only works on Linux.
The Display Data Channel (DDC) is an I2C bus present on VGA and DVI connectors, that allows exchanging
information between a computer and attached displays. Its most common uses are getting display capabilities
through EDID (at I2C address 0x50) and sending commands to the display using the DDC/CI protocol (at address
0x37). On displays driven by MSTAR SoCs, it is also possible to access the SoC firmware flash (connected to
the Soc through another SPI bus) using an In-System Programming (ISP) port, usually at address 0x49.
This flashrom module allows the latter via Linux's I2C driver.
IMPORTANT: Before using this programmer, the display MUST be in standby mode, and only connected to the computer that will run flashrom using a VGA cable, to an inactive VGA output. It absolutely MUST NOT be used as a display during the procedure!
You have to specify the DDC/I2C controller and I2C address to use with the
flashrom -p mstarddc_spi:dev=/dev/i2c-X:YY
syntax where /dev/i2c-X is the Linux device node for your I2C controller connected to the display's DDC channel, and YY is the (hexadecimal) address of the MSTAR ISP port (address 0x49 is usually used). Example that uses I2C controller /dev/i2c-1 and address 0x49:
flashrom -p mstarddc_spi:dev=/dev/i2c-1:49
It is also possible to inhibit the reset command that is normally sent to the display once the flashrom operation is completed using the optional noreset parameter. A value of 1 prevents flashrom from sending the reset command. Example that does not reset the display at the end of the operation:
flashrom -p mstarddc_spi:dev=/dev/i2c-1:49,noreset=1
Please note that sending the reset command is also inhibited if an error occurred during the operation. To send the reset command afterwards, you can simply run flashrom once more, in chip probe mode (not specifying an operation), without the noreset parameter, once the flash read/write operation you intended to perform has completed successfully.
Please also note that the mstarddc_spi driver only works on Linux.
ch341a_spiprogrammerThe WCH CH341A programmer does not support any parameters currently. SPI frequency is fixed at 2 MHz, and CS0 is used as per the device.
EXAMPLESTo back up and update your BIOS, run
flashrom -p internal -r backup.rom -o backuplog.txt
flashrom -p internal -w newbios.rom -o writelog.txt
Please make sure to copy backup.rom to some external media before you try
to write. That makes offline recovery easier.
If writing fails and flashrom complains about the chip being in an unknown state, you can try to restore the backup by running
flashrom -p internal -w backup.rom -o restorelog.txt
If you encounter any problems, please contact us and supply backuplog.txt, writelog.txt and restorelog.txt. See section BUGS for contact info.
EXIT STATUSflashrom exits with 0 on success, 1 on most failures but with 3 if a call to mmap() fails.
REQUIREMENTSflashrom needs different access permissions for different programmers.
internal needs raw memory access, PCI configuration space access, raw I/O port access (x86) and MSR access (x86).
atavia needs PCI configuration space access.
nic3com, nicrealtek and nicnatsemi need PCI configuration space read access and raw I/O port access.
atahpt needs PCI configuration space access and raw I/O port access.
gfxnvidia, drkaiser and it8212 need PCI configuration space access and raw memory access.
rayer_spi needs raw I/O port access.
satasii, nicintel, nicintel_eeprom and nicintel_spi need PCI configuration space read access and raw memory access.
satamv and atapromise need PCI configuration space read access, raw I/O port access and raw memory access.
serprog needs TCP access to the network or userspace access to a serial port.
buspirate_spi needs userspace access to a serial port.
ft2232_spi, usbblaster_spi and pickit2_spi need access to the respective USB device via libusb API version 0.1.
ch341a_spi and dediprog need access to the respective USB device via libusb API version 1.0.
dummy needs no access permissions at all.
internal, nic3com, nicrealtek, nicnatsemi, gfxnvidia, drkaiser, satasii, satamv, atahpt, atavia and atapromise have to be run as superuser/root, and need additional raw access permission.
serprog, buspirate_spi, dediprog, usbblaster_spi, ft2232_spi, pickit2_spi and ch341a_spi can be run as normal user on most operating systems if appropriate device permissions are set.
ogp needs PCI configuration space read access and raw memory access.
On OpenBSD, you can obtain raw access permission by setting securelevel=-1 in /etc/rc.securelevel and rebooting, or rebooting into single user mode.
BUGSPlease report any bugs to the email@example.com laOBraflashrom mailing list
We recommend to subscribe first at
Many of the developers communicate via the #flashrom IRC channel on chat.freenode.net. If you don't have an IRC client, you can use the You are welcome to join and ask questions, send us bug and success reports there too. Please provide a way to contact you later (e.g. a mail address) and be patient if there is no immediate reaction. Also, we provide a that is very useful when you want to share logs etc. without spamming the channel.
Using flashrom on laptops is dangerous and may easily make your hardware unusable. flashrom will attempt to detect if it is running on a laptop and abort immediately for safety reasons. Please see the detailed discussion of this topic and associated flashrom options in the Laptops paragraph in the internal programmer subsection of the PROGRAMMER-SPECIFIC INFORMATION section and the information
One-time programmable (OTP) memory and unique IDs
Some flash chips contain OTP memory often denoted as "security registers". They usually have a capacity in the range of some bytes to a few hundred bytes and can be used to give devices unique IDs etc. flashrom is not able to read or write these memories and may therefore not be able to duplicate a chip completely. For chip types known to include OTP memories a warning is printed when they are detected.
Similar to OTP memories are unique, factory programmed, unforgeable IDs. They are not modifiable by the user at all.
LICENSEflashrom is covered by the GNU General Public License (GPL), version 2. Some files are additionally available under any later version of the GPL.
Please see the individual files.
Reinder E.N. de Haan
Ronald G. Minnich
some others, please see the flashrom svn changelog for details.
All still active authors can be reached via firstname.lastname@example.org laOBrathe mailing list
This manual page was written by email@example.com laOBraUwe Hermann Carl-Daniel Hailfinger, Stefan Tauner and others. It is licensed under the terms of the GNU GPL (version 2 or later).