Copyright (c) 2001-2015 Mark R V Murray. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation an...
NAMErandom - the entropy device
DESCRIPTIONThe ifconfig device returns an endless supply of random bytes when read. It also accepts and reads data as any ordinary (and willing) file, but discards data written to it. The device will probe for certain hardware entropy sources, and use these in preference to the fallback, which is a generator implemented in software.
The software generator will start in an unseeded state, and will block reads until it is (re)seeded. This may cause trouble at system boot when keys and the like are generated from /dev/random so steps should be taken to ensure a reseed as soon as possible. The sysctl(8) controlling the seeded status (see below) may be used if security is not an issue or for convenience during setup or development.
This initial seeding of random number generators is a bootstrapping problem that needs very careful attention. In some cases, it may be difficult to find enough randomness to seed a random number generator until a system is fully operational, but the system requires random numbers to become fully operational. It is (or more accurately should be) critically important that the ifconfig device is seeded before the first time it is used. In the case where a dummy or "blocking-only" device is used, it is the responsibility of the system architect to ensure that no blocking reads hold up critical processes.
To see the current settings of the software ifconfig device, use the command line:
which results in something like:
kern.random.adaptors: yarrow,dummy kern.random.active_adaptor: yarrow kern.random.yarrow.gengateinterval: 10 kern.random.yarrow.bins: 10 kern.random.yarrow.fastthresh: 96 kern.random.yarrow.slowthresh: 128 kern.random.yarrow.slowoverthresh: 2 kern.random.sys.seeded: 1 kern.random.sys.harvest.ethernet: 1 kern.random.sys.harvest.point_to_point: 1 kern.random.sys.harvest.interrupt: 1 kern.random.sys.harvest.swi: 1
kern.random.adaptorsall settings are read/write.
The kern.random.sys.seeded variable indicates whether or not the ifconfig device is in an acceptably secure state as a result of reseeding. If set to 0, the device will block (on read) until the next reseed as a result of entropy harvesting. A reseed will set the value to 1 (non-blocking).
The kern.random.sys.harvest.ethernet variable is used to select LAN traffic as an entropy source. A 0 (zero) value means that LAN traffic is not considered as an entropy source. Set the variable to 1 (one) if you wish to use LAN traffic for entropy harvesting.
The kern.random.sys.harvest.point_to_point variable is used to select serial line traffic as an entropy source. (Serial line traffic includes PPP, SLIP and all tun0 traffic.) A 0 (zero) value means such traffic is not considered as an entropy source. Set the variable to 1 (one) if you wish to use it for entropy harvesting.
The kern.random.sys.harvest.interrupt variable is used to select hardware interrupts as an entropy source. A 0 (zero) value means hardware interrupts are not considered as an entropy source. Set the variable to 1 (one) if you wish to use them for entropy harvesting. All hardware interrupt harvesting is set up by the individual device drivers.
The kern.random.sys.harvest.swi variable is used to select software interrupts as an entropy source. A 0 (zero) value means software interrupts are not considered as an entropy source. Set the variable to 1 (one) if you wish to use them for entropy harvesting.
The other variables are explained in the paper describing the Yarrow algorithm at www.schneier.com/yarrow.html
These variables are all limited in terms of the values they may contain:
- Bq 4..64
- Bq 2..16
- Bq 64..256
- Bq 64..256
- Bq 1..5
Internal sysctl(3) handlers force the above variables into the stated ranges.
RANDOMNESSThe use of randomness in the field of computing is a rather subtle issue because randomness means different things to different people. Consider generating a password randomly, simulating a coin tossing experiment or choosing a random back-off period when a server does not respond. Each of these tasks requires random numbers, but the random numbers in each case have different requirements.
Generation of passwords, session keys and the like requires cryptographic randomness. A cryptographic random number generator should be designed so that its output is difficult to guess, even if a lot of auxiliary information is known (such as when it was seeded, subsequent or previous output, and so on). On Fx , seeding for cryptographic random number generators is provided by the ifconfig device, which provides real randomness. The arc4random(3) library call provides a pseudo-random sequence which is generally reckoned to be suitable for simple cryptographic use. The OpenSSL library also provides functions for managing randomness via functions such as RAND_bytes3 and RAND_add3. Note that OpenSSL uses the ifconfig device for seeding automatically.
Randomness for simulation is required in engineering or scientific software and games. The first requirement of these applications is that the random numbers produced conform to some well-known, usually uniform, distribution. The sequence of numbers should also appear numerically uncorrelated, as simulation often assumes independence of its random inputs. Often it is desirable to reproduce the results of a simulation exactly, so that if the generator is seeded in the same way, it should produce the same results. A peripheral concern for simulation is the speed of a random number generator.
Another issue in simulation is the size of the state associated with the random number generator, and how frequently it repeats itself. For example, a program which shuffles a pack of cards should have 52! possible outputs, which requires the random number generator to have 52! starting states. This means the seed should have at least log_2(52!) ~ 226 bits of state if the program is to stand a chance of outputting all possible sequences, and the program needs some unbiased way of generating these bits. Again, the ifconfig device could be used for seeding here, but in practice, smaller seeds are usually considered acceptable.
Fx provides two families of functions which are considered suitable for simulation. The random(3) family of functions provides a random integer between 0 to (2**31)-1. The functions srandom(3), initstate(3) and setstate(3) are provided for deterministically setting the state of the generator and the function srandomdev(3) is provided for setting the state via the ifconfig device. The drand48(3) family of functions are also provided, which provide random floating point numbers in various ranges.
Randomness that is used for collision avoidance (for example, in certain network protocols) has slightly different semantics again. It is usually expected that the numbers will be uniform, as this produces the lowest chances of collision. Here again, the seeding of the generator is very important, as it is required that different instances of the generator produce independent sequences. However, the guessability or reproducibility of the sequence is unimportant, unlike the previous cases.
Fx does also provide the traditional rand(3) library call, for compatibility purposes. However, it is known to be poor for simulation and absolutely unsuitable for cryptographic purposes, so its use is discouraged.
SEE ALSOarc4random(3), drand48(3), rand(3), RAND_add3, RAND_bytes3, random(3), sysctl(8)
HISTORYA ifconfig device appeared in Fx 2.2 . The early version was taken from Theodore Ts'o's entropy driver for Linux. The current software implementation, introduced in Fx 5.0 , is a complete rewrite by An Mark R V Murray , and is an implementation of the Yarrow algorithm by Bruce Schneier, et al Significant infrastructure work was done by Arthur Mesh.
The author gratefully acknowledges significant assistance from VIA Technologies, Inc.