igb (4)
Leading comments
Copyright (c) 2001-2003, Intel Corporation All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation...
NAME
igb - Intel(R) PRO/1000 PCI Express Gigabit Ethernet adapter driverSYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:device igb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:
if_igb_load="YES"
DESCRIPTION
The ifconfig driver provides support for PCI Express Gigabit Ethernet adapters based on the Intel 82575 and 82576 Ethernet controller chips. The driver supports Transmit/Receive checksum offload and Jumbo Frames. Furthermore it supports TCP segmentation offload (TSO) on all adapters. The identification LEDs of the adapters supported by the ifconfig driver can be controlled via the led(4) API for localization purposes.For questions related to hardware requirements, refer to the documentation supplied with your Intel PRO/1000 adapter. All hardware requirements listed apply to use with Fx .
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 9216.
This driver supports hardware assisted VLANs. The ifconfig driver supports the following media types:
- autoselect
- Enables auto-negotiation for speed and duplex.
- 10baseT/UTP
- Sets 10Mbps operation. Use the mediaopt option to select full-duplex mode.
- 100baseTX
- Sets 100Mbps operation. Use the mediaopt option to select full-duplex mode.
- 1000baseSX
- Sets 1000Mbps operation. Only full-duplex mode is supported at this speed.
- 1000baseTX
- Sets 1000Mbps operation. Only full-duplex mode is supported at this speed.
The ifconfig driver supports the following media options:
- full-duplex
- Forces full-duplex operation
- half-duplex
- Forces half-duplex operation.
Only use mediaopt to set the driver to full-duplex If mediaopt is not specified, the driver defaults to half-duplex
For more information on configuring this device, see ifconfig(8).
HARDWARE
The ifconfig driver supports Gigabit Ethernet adapters based on the Intel 82575 and 82576 controller chips:
- Intel Gigabit ET Dual Port Server Adapter (82576)
- Intel Gigabit VT Quad Port Server Adapter (82575)
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf5.- hw.igb.rxd
- Number of receive descriptors allocated by the driver. The default value is 1024. The minimum is 80, and the maximum is 4096.
- hw.igb.txd
- Number of transmit descriptors allocated by the driver. The default value is 1024. The minimum is 80, and the maximum is 4096.
- hw.igb.enable_aim
- If set to 1, enable Adaptive Interrupt Moderation. The default is to enable Adaptive Interrupt Moderation.
- hw.igb.num_queues
- Number of queues used for data transfer. If set to 0, number of queues will be configured automatically based on number of CPUs and max supported MSI-X messages on the device.
- kern.ipc.nmbclusters
- The maximum number of mbuf clusters allowed. If the system has more than one igb card or jumbo frames are enabled, this value will need to be increased.
- kern.ipc.nmbjumbo9k
- The maximum number of mbuf 9k jumbo clusters allowed. Increasing this to allow for at least 8192 extra clusters per interface can allow for an mtu of 8192.
FILES
- /dev/led/igb*
- identification LED device nodes
EXAMPLES
Make the identification LED of igb0 blink:
"echo f2 > /dev/led/igb0"
Turn the identification LED of igb0 off again:
"echo 0 > /dev/led/igb0"
DIAGNOSTICS
- "igb%d: Unable to allocate bus resource: memory"
- A fatal initialization error has occurred.
- "igb%d: Unable to allocate bus resource: interrupt"
- A fatal initialization error has occurred.
- "igb%d: watchdog timeout -- resetting"
- The device has stopped responding to the network, or there is a problem with the network connection (cable).
SUPPORT
For general information and support, go to the Intel support website at: support.intel.comIf an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related to the issue to Aq freebsd@intel.com .