if_stf (4)
Leading comments
$KAME: stf.4,v 1.35 2001/05/02 06:24:49 itojun Exp $ Copyright (C) 1995, 1996, 1997, and 1998 WIDE Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this lis...
NAME
stf - 6to4 tunnel interfaceSYNOPSIS
device stfDESCRIPTION
The ifconfig interface supports ``6to4'' IPv6 in IPv4 encapsulation. It can tunnel IPv6 traffic over IPv4, as specified in RFC3056For ordinary nodes in 6to4 site, you do not need ifconfig interface. The ifconfig interface is necessary for site border router (called ``6to4 router'' in the specification).
Each ifconfig interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf5.
Due to the way 6to4 protocol is specified, ifconfig interface requires certain configuration to work properly. Single (no more than 1) valid 6to4 address needs to be configured to the interface. ``A valid 6to4 address'' is an address which has the following properties. If any of the following properties are not satisfied, ifconfig raises runtime error on packet transmission. Read the specification for more details.
- matches 2002:xxyy:zzuu::/48 where xxyy:zzuu is a hexadecimal notation of an IPv4 address for the node. IPv4 address can be taken from any of interfaces your node has. Since the specification forbids the use of IPv4 private address, the address needs to be a global IPv4 address.
- Subnet identifier portion (48th to 63rd bit) and interface identifier portion (lower 64 bits) are properly filled to avoid address collisions.
If you would like the node to behave as a relay router, the prefix length for the IPv6 interface address needs to be 16 so that the node would consider any 6to4 destination as ``on-link'' If you would like to restrict 6to4 peers to be inside certain IPv4 prefix, you may want to configure IPv6 prefix length as ``16 + IPv4 prefix length'' ifconfig interface will check the IPv4 source address on packets, if the IPv6 prefix length is larger than 16.
ifconfig can be configured to be ECN friendly. This can be configured by IFF_LINK1 See gif(4) for details.
Please note that 6to4 specification is written as ``accept tunnelled packet from everyone'' tunnelling device. By enabling ifconfig device, you are making it much easier for malicious parties to inject fabricated IPv6 packet to your node. Also, malicious party can inject an IPv6 packet with fabricated source address to make your node generate improper tunnelled packet. Administrators must take caution when enabling the interface. To prevent possible attacks, ifconfig interface filters out the following packets. Note that the checks are no way complete:
- Packets with IPv4 unspecified address as outer IPv4 source/destination (0.0.0.0/8 )
- Packets with loopback address as outer IPv4 source/destination (127.0.0.0/8 )
- Packets with IPv4 multicast address as outer IPv4 source/destination (224.0.0.0/4 )
- Packets with limited broadcast address as outer IPv4 source/destination (255.0.0.0/8 )
- Packets with private address as outer IPv4 source/destination (10.0.0.0/8 , 172.16.0.0/12 , 192.168.0.0/16 )
- Packets with subnet broadcast address as outer IPv4 source/destination. The check is made against subnet broadcast addresses for all of the directly connected subnets.
- Packets that does not pass ingress filtering. Outer IPv4 source address must meet the IPv4 topology on the routing table. Ingress filter can be turned off by IFF_LINK2 bit.
- The same set of rules are applied against the IPv4 address embedded into inner IPv6 address, if the IPv6 address matches 6to4 prefix.
It is recommended to filter/audit incoming IPv4 packet with IP protocol number 41, as necessary. It is also recommended to filter/audit encapsulated IPv6 packets as well. You may also want to run normal ingress filter against inner IPv6 address to avoid spoofing.
By setting the IFF_LINK0 flag on the ifconfig interface, it is possible to disable the input path, making the direct attacks from the outside impossible. Note, however, there are other security risks exist. If you wish to use the configuration, you must not advertise your 6to4 address to others.
SYSCTL VARIABLES
The following sysctl(8) variables can be used to control the behavior of the stf The default value is shown next to each variable.- net.link.stf.permit_rfc1918 : 0
- The RFC3056 requires the use of globally unique 32-bit IPv4 addresses. This sysctl variable controls the behaviour of this requirement. When it set to not 0, stf allows the use of private IPv4 addresses described in the RFC1918. This may be useful for an Intranet environment or when some mechanisms of network address translation (NAT) are used.
EXAMPLES
Note that 8504:0506 is equal to 133.4.5.6 written in hexadecimals.
# ifconfig ne0 inet 133.4.5.6 netmask 0xffffff00
# ifconfig stf0 inet6 2002:8504:0506:0000:a00:5aff:fe38:6f86 \
prefixlen 16 alias
The following configuration accepts packets from IPv4 source 9.1.0.0/16 only. It emits 6to4 packet only for IPv6 destination 2002:0901::/32 (IPv4 destination will match 9.1.0.0/16 )
# ifconfig ne0 inet 9.1.2.3 netmask 0xffff0000
# ifconfig stf0 inet6 2002:0901:0203:0000:a00:5aff:fe38:6f86 \
prefixlen 32 alias
The following configuration uses the ifconfig interface as an output-only device. You need to have alternative IPv6 connectivity (other than 6to4) to use this configuration. For outbound traffic, you can reach other 6to4 networks efficiently via stf For inbound traffic, you will not receive any 6to4-tunneled packets (less security drawbacks). Be careful not to advertise your 6to4 prefix to others (2002:8504:0506::/48 ) and not to use your 6to4 prefix as a source.
# ifconfig ne0 inet 133.4.5.6 netmask 0xffffff00
# ifconfig stf0 inet6 2002:8504:0506:0000:a00:5aff:fe38:6f86 \
prefixlen 16 alias deprecated link0
# route add -inet6 2002:: -prefixlen 16 ::1
# route change -inet6 2002:: -prefixlen 16 ::1 -ifp stf0
SEE ALSO
gif(4), inet(4), inet6(4)www.ipv6day.org/action.php?n=En.IPv6day
- Brian Carpenter Keith Moore "Connection of IPv6 Domains via IPv4 Clouds" February 2001 RFC 3056
- Jun-ichiro itojun Hagino "Possible abuse against IPv6 transition technologies" July 2000 draft-itojun-ipv6-transition-abuse-01.txt work in progress