if_patm (4)

Leading comments

 Copyright (c) 2003
	Fraunhofer Institute for Open Communication Systems (FhG Fokus).
 	All rights reserved.

 Redistribution and use in source and binary forms, with or without
 modification, are permitted provided that the following conditions
 are met:
 1. Redistributions of source code must retain the above copyright
    notice, this list of conditions and the following disclaimer.
 2. Redistributions in binary form must reproduce the above copyright
    notice, this list of conditions an...

(The comments found at the beginning of the groff file "man4/if_patm.4freebsd".)

NAME

patm - device driver for IDT77252 based ATM interfaces (ProSum and IDT)

SYNOPSIS

device patm device utopia device atm

options NATM options LIBMBPOOL

DESCRIPTION

The ifconfig device driver supports ATM cards based on the IDT77252 chip. It has been tested with ProSum's ProATM-155 cards and with IDT's evaluation boards. The driver interfaces with the natm(4) framework, netgraph(4) and HARP. It provides only PVC services. Signalling, ATMARP, ILMI and other higher layer protocols are implemented using netgraph(4) or HARP.

For configuring the card for IP see natmip(4).

The driver supports UBR, CBR, VBR and ABR traffic. Supported AALs are: AAL0 (cell payloads), AAL5 and raw AAL. The driver supports opening of VCI/VPI 0/0 in RX, raw AAL-mode. This VC will receive all incoming cells (even those with non-zero GFC fields and VPI/VCI values outside the allowed range) that are not claimed by other open connections. This may be used for monitoring purposes.

The following sysctls are recognized by the driver additionally to those handled by utopia(4):

hw.atm.patm N .istats

Returns a list of Vt uint32_t statistic counters with internal driver statistics.

hw.atm.patm N .eeprom

This is a read-only variable containing the contents of the on-board EEPROM device.

hw.atm.patm N .lbuf_max

This puts an upper limit on the number of large receive buffers the driver will allocate. This is a read-only variable that can be set via a loader(8) tunable.

hw.atm.patm N .tx_maxmaps

This is the upper limit of transmission DMA maps the driver will allocate. This is read-only but may be set via a loader(8) tunable.

hw.atm.patm N .debug

Bf Em (Only if debugging enabled.) Ef These are debugging flags. See src/sys/dev/patm/if_patmvar.h for the possible flags. This may be initialized via a loader(8) tunable.

hw.atm.patm N .regs

Bf Em (Only if debugging enabled.) Ef Returns the current values of the card's registers.

hw.atm.patm N .tsq

Returns the transmit status queue.

When loaded, the driver initializes several variables from loader(8) tunables:

hw.patm N .lbuf_max

This initializes the corresponding sysctl(8) variable and defines an upper limit on the number of large receive buffers (mbuf clusters).

hw.patm N .tx_maxmaps

This initializes the corresponding sysctl(8) variable and is the maximum number of DMA maps for transmission that the driver will allocated.

hw.patm N .debug

Bf Em (Only if debugging enabled.) Ef Initializes the debugging flags.

The driver supports the media options sdh , noscramb and unassigned (see utopia(4)) when the card is a 155MBit card. Both PMC-Sierra S/UNI and IDT77155 PHY chips are supported for these cards. For 25MBit cards the IDT77105 is supported.

DIAGNOSTICS

patm1: <NICStAR (77222/77252) ATM adapter> port 0xc000-0xc0ff mem 0xf8000000-0xf83fffff,0xf4000000-0xf4000fff irq 11 at device 8.0 on pci2
patm1: IDT77252 155MBit interface; idt77252 Rev. G; IDT77155 PHY
patm1: 128K x 32 SRAM; 4096 connections

SEE ALSO

natm(4), natmip(4), utopia(4)

ACKNOWLEDGEMENTS

Thanks to Christian Bucari from ProSum for lending two of these cards to enable the development of this driver. Thanks also for answering my questions.

AUTHORS

An Harti Brandt Aq harti@FreeBSD.org

CAVEATS

The card fails to generate an interrupt if a cell is received in AAL0 mode that has the MSB of the PTI field cleared. Therefore cells will be delivered on the next receive interrupt which can happen either when the receive status queue is full, or a cell with the last bit of the PTI set is received.

Although the card supports AAL3/4 the driver does not.

The rate tables used by this driver are not the tables recommended by IDT (they are wrong anyway). The driver's tables are slightly more aggressive than IDT's. That means, that the actual cell rate can be slightly higher than the specified. This is in contrast to the IDT tables where cell rates 5% less than the allowed one have been observed. This can be changed by changing the program that generates these tables, found in /usr/src/sys/dev/patm/genrtab and regenerating them.

The reported media for the 155MBit cards will always be OC3/MM, because there is no (known to me) way to figure out the actual medium. The medium should really be coded in the EEPROM by the manufacturer.

The Tx cell counter in the utopia statistics is wrong, because the chip uses idle cells for spacing and the PHY counts these cells. While there is a configuration option for the chip to switch of these cells and, according to the documentation, this should not influence cell spacing, it does, so the driver lets the chip generate idle cells.