if_nfe (4)
Leading comments
$OpenBSD: nfe.4,v 1.7 2006/02/28 08:13:47 jsg Exp $ Copyright (c) 2006 Jonathan Gray <jsg@openbsd.org> Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies. THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVE...
NAME
nfe - NVIDIA nForce MCP Ethernet driverSYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:device miibus device nfe
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf5:
if_nfe_load="YES"
DESCRIPTION
The ifconfig driver supports PCI Ethernet adapters based on the NVIDIA nForce Media and Communications Processors (MCP), such as the nForce, nForce 2, nForce 3, CK804, MCP04, MCP51, MCP55, MCP61, MCP65, MCP67, MCP73, MCP77 and MCP79 Ethernet controller chips.Supported features include (hardware support provided):
- Receive/Transmit IP/TCP/UDP checksum offload
- Hardware VLAN tag insertion/stripping
- TCP segmentation offload (TSO)
- MSI/MSI-X
- Jumbo Frames
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility configures the adapter to receive and transmit Jumbo Frames.
The ifconfig driver supports the following media types:
- autoselect
- Enable autoselection of the media type and options.
- 10baseT/UTP
- Set 10Mbps operation.
- 100baseTX
- Set 100Mbps (Fast Ethernet) operation.
- 1000baseT
- Set 1000Mbps (Gigabit Ethernet) operation (recent models only).
The ifconfig driver supports the following media options:
- half-duplex
- Force half duplex operation.
- full-duplex
- Force full duplex operation.
For more information on configuring this device, see ifconfig(8).
HARDWARE
The ifconfig driver supports the following NVIDIA MCP onboard adapters:
- NVIDIA nForce MCP Networking Adapter
- NVIDIA nForce MCP04 Networking Adapter
- NVIDIA nForce 430 MCP12 Networking Adapter
- NVIDIA nForce 430 MCP13 Networking Adapter
- NVIDIA nForce MCP51 Networking Adapter
- NVIDIA nForce MCP55 Networking Adapter
- NVIDIA nForce MCP61 Networking Adapter
- NVIDIA nForce MCP65 Networking Adapter
- NVIDIA nForce MCP67 Networking Adapter
- NVIDIA nForce MCP73 Networking Adapter
- NVIDIA nForce MCP77 Networking Adapter
- NVIDIA nForce MCP79 Networking Adapter
- NVIDIA nForce2 MCP2 Networking Adapter
- NVIDIA nForce2 400 MCP4 Networking Adapter
- NVIDIA nForce2 400 MCP5 Networking Adapter
- NVIDIA nForce3 MCP3 Networking Adapter
- NVIDIA nForce3 250 MCP6 Networking Adapter
- NVIDIA nForce3 MCP7 Networking Adapter
- NVIDIA nForce4 CK804 MCP8 Networking Adapter
- NVIDIA nForce4 CK804 MCP9 Networking Adapter
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf5.- hw.nfe.msi_disable
- Whether or not MSI support is enabled in the driver. The default value is 0.
- hw.nfe.msix_disable
- Whether or not MSI-X support is enabled in the driver. The default value is 0.
SYSCTL VARIABLES
The following sysctl(8) variables can be used to modify or monitor ifconfig behavior.- dev.nfe.%d.process_limit
- Maximum number of Rx events to be processed in the event loop before rescheduling a taskqueue. The accepted range is 50 to 255, the default value is 192. The interface does not need to be brought down and up again before a change takes effect.