Copyright (c) 1991, 1993 The Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following...
NAMEmadvise , posix_madvise - give advice about use of memory
SYNOPSISIn sys/mman.h Ft int Fn madvise void *addr size_t len int behav Ft int Fn posix_madvise void *addr size_t len int behav
DESCRIPTIONThe Fn madvise system call allows a process that has knowledge of its memory behavior to describe it to the system. The Fn posix_madvise interface is identical, except it returns an error number on error and does not modify errno and is provided for standards conformance.
The known behaviors are:
- Tells the system to revert to the default paging behavior.
- Is a hint that pages will be accessed randomly, and prefetching is likely not advantageous.
- Causes the VM system to depress the priority of pages immediately preceding a given page when it is faulted in.
- Causes pages that are in a given virtual address range to temporarily have higher priority, and if they are in memory, decrease the likelihood of them being freed. Additionally, the pages that are already in memory will be immediately mapped into the process, thereby eliminating unnecessary overhead of going through the entire process of faulting the pages in. This WILL NOT fault pages in from backing store, but quickly map the pages already in memory into the calling process.
- Allows the VM system to decrease the in-memory priority of pages in the specified range. Additionally future references to this address range will incur a page fault.
- Gives the VM system the freedom to free pages, and tells the system that information in the specified page range is no longer important. This is an efficient way of allowing malloc(3) to free pages anywhere in the address space, while keeping the address space valid. The next time that the page is referenced, the page might be demand zeroed, or might contain the data that was there before the MADV_FREE call. References made to that address space range will not make the VM system page the information back in from backing store until the page is modified again.
Request that the system not flush the data associated with this map to
physical backing store unless it needs to.
Typically this prevents the
file system update daemon from gratuitously writing pages dirtied
by the VM system to physical disk.
Note that VM/file system coherency is
always maintained, this feature simply ensures that the mapped data is
only flush when it needs to be, usually by the system pager.
This feature is typically used when you want to use a file-backed shared memory area to communicate between processes (IPC) and do not particularly need the data being stored in that area to be physically written to disk. With this feature you get the equivalent performance with mmap that you would expect to get with SysV shared memory calls, but in a more controllable and less restrictive manner. However, note that this feature is not portable across UNIX platforms (though some may do the right thing by default). For more information see the MAP_NOSYNC section of mmap(2)
- Undoes the effects of MADV_NOSYNC for any future pages dirtied within the address range. The effect on pages already dirtied is indeterminate - they may or may not be reverted. You can guarantee reversion by using the msync(2) or fsync(2) system calls.
- Region is not included in a core file.
- Include region in a core file.
- Informs the VM system this process should not be killed when the swap space is exhausted. The process must have superuser privileges. This should be used judiciously in processes that must remain running for the system to properly function.
Portable programs that call the Fn posix_madvise interface should use the aliases POSIX_MADV_NORMAL , POSIX_MADV_SEQUENTIAL POSIX_MADV_RANDOM , POSIX_MADV_WILLNEED and POSIX_MADV_DONTNEED rather than the flags described above.
RETURN VALUESRv -std madvise
ERRORSThe Fn madvise system call will fail if:
- Bq Er EINVAL
- The Fa behav argument is not valid.
- Bq Er ENOMEM
- The virtual address range specified by the Fa addr and Fa len arguments is not valid.
- Bq Er EPERM
- MADV_PROTECT was specified and the process does not have superuser privileges.