systemd 229 +PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN

systemctl [OPTIONS...] {COMMAND} ... Query or send control commands to the systemd manager. -h --help Show this help --version Show package version --system Connect to system manager --user Connect to user service manager -H --host=[USER@]HOST Operate on remote host -M --machine=CONTAINER Operate on local container -t --type=TYPE List units of a particular type --state=STATE List units with particular LOAD or SUB or ACTIVE state -p --property=NAME Show only properties by this name -a --all Show all loaded units/properties, including dead/empty ones. To list all units installed on the system, use the 'list-unit-files' command instead. -l --full Don't ellipsize unit names on output -r --recursive Show unit list of host and local containers --reverse Show reverse dependencies with 'list-dependencies' --job-mode=MODE Specify how to deal with already queued jobs, when queueing a new job --show-types When showing sockets, explicitly show their type -i --ignore-inhibitors When shutting down or sleeping, ignore inhibitors --kill-who=WHO Who to send signal to -s --signal=SIGNAL Which signal to send --now Start or stop unit in addition to enabling or disabling it -q --quiet Suppress output --no-block Do not wait until operation finished --no-wall Don't send wall message before halt/power-off/reboot --no-reload Don't reload daemon after en-/dis-abling unit files --no-legend Do not print a legend (column headers and hints) --no-pager Do not pipe output into a pager --no-ask-password Do not ask for system passwords --global Enable/disable unit files globally --runtime Enable unit files only temporarily until next reboot -f --force When enabling unit files, override existing symlinks When shutting down, execute action immediately --preset-mode= Apply only enable, only disable, or all presets --root=PATH Enable unit files in the specified root directory -n --lines=INTEGER Number of journal entries to show -o --output=STRING Change journal output mode (short, short-iso, short-precise, short-monotonic, verbose, export, json, json-pretty, json-sse, cat) --firmware-setup Tell the firmware to show the setup menu on next boot --plain Print unit dependencies as a list instead of a tree Unit Commands: list-units [PATTERN...] List loaded units list-sockets [PATTERN...] List loaded sockets ordered by address list-timers [PATTERN...] List loaded timers ordered by next elapse start NAME... Start (activate) one or more units stop NAME... Stop (deactivate) one or more units reload NAME... Reload one or more units restart NAME... Start or restart one or more units try-restart NAME... Restart one or more units if active reload-or-restart NAME... Reload one or more units if possible, otherwise start or restart try-reload-or-restart NAME... If active, reload one or more units, if supported, otherwise restart isolate NAME Start one unit and stop all others kill NAME... Send signal to processes of a unit is-active PATTERN... Check whether units are active is-failed PATTERN... Check whether units are failed status [PATTERN...|PID...] Show runtime status of one or more units show [PATTERN...|JOB...] Show properties of one or more units/jobs or the manager cat PATTERN... Show files and drop-ins of one or more units set-property NAME ASSIGNMENT... Sets one or more properties of a unit help PATTERN...|PID... Show manual for one or more units reset-failed [PATTERN...] Reset failed state for all, one, or more units list-dependencies [NAME] Recursively show units which are required or wanted by this unit or by which this unit is required or wanted Unit File Commands: list-unit-files [PATTERN...] List installed unit files enable NAME... Enable one or more unit files disable NAME... Disable one or more unit files reenable NAME... Reenable one or more unit files preset NAME... Enable/disable one or more unit files based on preset configuration preset-all Enable/disable all unit files based on preset configuration is-enabled NAME... Check whether unit files are enabled mask NAME... Mask one or more units unmask NAME... Unmask one or more units link PATH... Link one or more units files into the search path add-wants TARGET NAME... Add 'Wants' dependency for the target on specified one or more units add-requires TARGET NAME... Add 'Requires' dependency for the target on specified one or more units edit NAME... Edit one or more unit files get-default Get the name of the default target set-default NAME Set the default target Machine Commands: list-machines [PATTERN...] List local containers and host Job Commands: list-jobs [PATTERN...] List jobs cancel [JOB...] Cancel all, one, or more jobs Environment Commands: show-environment Dump environment set-environment NAME=VALUE... Set one or more environment variables unset-environment NAME... Unset one or more environment variables import-environment [NAME...] Import all or some environment variables Manager Lifecycle Commands: daemon-reload Reload systemd manager configuration daemon-reexec Reexecute systemd manager System Commands: is-system-running Check whether system is fully running default Enter system default mode rescue Enter system rescue mode emergency Enter system emergency mode halt Shut down and halt the system poweroff Shut down and power-off the system reboot [ARG] Shut down and reboot the system kexec Shut down and reboot the system with kexec exit [EXIT_CODE] Request user instance or container exit switch-root ROOT [INIT] Change to a different root file system suspend Suspend the system hibernate Hibernate the system hybrid-sleep Hibernate and suspend the system