ipmitool version 1.8.18

ipmitool version 1.8.18 usage: ipmitool [options...] <command> -h This help -V Show version information -v Verbose (can use multiple times) -c Display output in comma separated format -d N Specify a /dev/ipmiN device to use (default=0) -I intf Interface to use -H hostname Remote host name for LAN interface -p port Remote RMCP port [default=623] -U username Remote session username -f file Read remote session password from file -z size Change Size of Communication Channel (OEM) -S sdr Use local file for remote SDR cache -D tty:b[:s] Specify the serial device, baud rate to use and, optionally, specify that interface is the system one -4 Use only IPv4 -6 Use only IPv6 -a Prompt for remote password -Y Prompt for the Kg key for IPMIv2 authentication -e char Set SOL escape character -C ciphersuite Cipher suite to be used by lanplus interface -k key Use Kg key for IPMIv2 authentication -y hex_key Use hexadecimal-encoded Kg key for IPMIv2 authentication -L level Remote session privilege level [default=ADMINISTRATOR] Append a '+' to use name/privilege lookup in RAKP1 -A authtype Force use of auth type NONE, PASSWORD, MD2, MD5 or OEM -P password Remote session password -E Read password from IPMI_PASSWORD environment variable -K Read kgkey from IPMI_KGKEY environment variable -m address Set local IPMB address -b channel Set destination channel for bridged request -t address Bridge request to remote target address -B channel Set transit channel for bridged request (dual bridge) -T address Set transit address for bridge request (dual bridge) -l lun Set destination lun for raw commands -o oemtype Setup for OEM (use 'list' to see available OEM types) -O seloem Use file for OEM SEL event descriptions -N seconds Specify timeout for lan [default=2] / lanplus [default=1] interface -R retry Set the number of retries for lan/lanplus interface [default=4] Interfaces: open Linux OpenIPMI Interface [default] imb Intel IMB Interface lan IPMI v1.5 LAN Interface lanplus IPMI v2.0 RMCP+ LAN Interface free FreeIPMI IPMI Interface serial-terminal Serial Interface, Terminal Mode serial-basic Serial Interface, Basic Mode dummy Linux DummyIPMI Interface usb IPMI USB Interface(OEM Interface for AMI Devices) Commands: raw Send a RAW IPMI request and print response i2c Send an I2C Master Write-Read command and print response spd Print SPD info from remote I2C device lan Configure LAN Channels chassis Get chassis status and set power state power Shortcut to chassis power commands event Send pre-defined events to MC mc Management Controller status and global enables sdr Print Sensor Data Repository entries and readings sensor Print detailed sensor information fru Print built-in FRU and scan SDR for FRU locators gendev Read/Write Device associated with Generic Device locators sdr sel Print System Event Log (SEL) pef Configure Platform Event Filtering (PEF) sol Configure and connect IPMIv2.0 Serial-over-LAN tsol Configure and connect with Tyan IPMIv1.5 Serial-over-LAN isol Configure IPMIv1.5 Serial-over-LAN user Configure Management Controller users channel Configure Management Controller channels session Print session information dcmi Data Center Management Interface nm Node Manager Interface sunoem OEM Commands for Sun servers kontronoem OEM Commands for Kontron devices picmg Run a PICMG/ATCA extended cmd fwum Update IPMC using Kontron OEM Firmware Update Manager firewall Configure Firmware Firewall delloem OEM Commands for Dell systems shell Launch interactive IPMI shell exec Run list of commands from file set Set runtime variable for shell and exec hpm Update HPM components using PICMG HPM.1 file ekanalyzer run FRU-Ekeying analyzer using FRU files ime Update Intel Manageability Engine Firmware vita Run a VITA 46.11 extended cmd lan6 Configure IPv6 LAN Channels